This article explains how to complete the air evacuation and bleed the circuit for outdoor units.

<h2 id="introduction"><u>Introduction</u></h2><p>This article explains how to complete the air evacuation and bleed the circuit for outdoor units.&#xA0;</p><p>The air and/or humidity left inside the refrigeration circuit can contaminate the refrigerant and cause abnormal spikes in pressure, leading to eventual compressor malfunctions. Therefore, after connecting the indoor and outdoor units to create a closed system, it is necessary to bleed the air and humidity out of the circuit by using a vacuum pump.&#xA0;</p><p>Perform the evacuation after the initial installation or when the unit is relocated. For first time installations, do not prematurely release the refrigerant prior to evacuation. Keep the valve caps sealed.&#xA0;</p><p id="isPasted">This article is for the following systems:&#xA0;</p><ul><li id="isPasted"><a href="https://www.pioneerminisplit.com/collections/diamante-essenza-high-wall-series" target="_blank" rel="noopener noreferrer">Diamante Essenza (WYT-17)</a></li><li><a href="https://www.pioneerminisplit.com/collections/diamante-pro-high-wall-series" target="_blank" rel="noopener noreferrer">Diamante Pro (WYT-20)</a></li><li><a href="https://www.pioneerminisplit.com/collections/quantum-ultra-high-wall-series" target="_blank" rel="noopener noreferrer">Quantum Ultra (WYT-24)</a></li><li><a href="https://www.pioneerminisplit.com/collections/quantum-hyperformance-high-wall-series" target="_blank" rel="noopener noreferrer">Quantum Hyperformance (WYT-25)</a></li><li><a href="https://www.pioneerminisplit.com/collections/quantum-fresh-series-breathe-the-difference" target="_blank" rel="noopener noreferrer">Quantum Fresh (WYT-FA)</a></li><li><a href="https://www.pioneerminisplit.com/collections/quantum-ultra-ceiling-cassette" target="_blank" rel="noopener noreferrer">Quantum Ultra Ceiling Cassette (CYT-24)</a></li><li><a href="https://www.pioneerminisplit.com/collections/quantum-ultra-ducted-ceiling-concealed" target="_blank" rel="noopener noreferrer">Quantum Ultra Ducted Ceiling Concealed (RYT-24)</a></li><li><a href="https://www.pioneerminisplit.com/collections/quantum-ultra-universal-flex-series" target="_blank" rel="noopener noreferrer">Quantum Ultra Floor-Ceiling Flex (UYT-24)</a></li></ul><h2 id="before-performing-the-evacuation"><u>Before Performing the Evacuation</u></h2><p>Check to make sure that both the high-pressure and low-pressure pipes between the indoor and outdoor units are connected properly.&#xA0;</p><p>Check to make sure all wiring is connected properly and is fully enclosed and insulated.&#xA0;</p><h2 id="steps"><u>Steps</u></h2><ol><li>Remove the caps from the 2-way and 3-way valves. Do not manipulate the valves until step 11.&#xA0;</li><li>Unscrew and remove the cap from the service port.&#xA0;<img src="https://attachments.gorgias.help/Q9r0k7BYaV2vg13y/hc/9JWjXVxG8m6DvMqm/2025120415-c724d09c-2414-4007-8f04-65804fd82340-wyt17_air_evacuation_step1&amp;2.png" style="width: 400px;" class="fr-fic fr-dib fr-bordered"></li><li>Connect the blue (low) hose of the manifold gauge to the service port on the outdoor unit&apos;s 3-way valve. Use an adapter if needed. Ensure that the pin fully engages the Schrader valve.&#xA0;</li><li>Connect the yellow (middle) hose from the manifold gauge to the vacuum pump.&#xA0;</li><li>Open the low pressure valve of the manifold gauge. Keep the high pressure valve closed.<img src="https://attachments.gorgias.help/Q9r0k7BYaV2vg13y/hc/9JWjXVxG8m6DvMqm/2025120415-c3c3a9ba-d373-409f-8557-e67d484d1b81-wyt17_air_evacuation_steps3-5.png" style="width: 400px;" class="fr-fic fr-dib fr-bordered"></li><li>Turn on the vacuum pump to evacuate the system.&#xA0;</li><li>Run the vacuum for at least 15 minutes or until the compound meters reads -76cmHG (-100kPa or -30 inHg). The vacuum reading should gradually decrease.&#xA0;</li><li>Close the low pressure side of the manifold gauge and turn off the vacuum pump.&#xA0;</li><li>For the best results, wait for at least 1 hour, then verify that there has been no increase in the vacuum reading.&#xA0;</li><li>If there is no change in the vacuum reading, unscrew the cap from the service valve (high pressure valve).&#xA0;</li><li>Insert the Allen wrench into the service valve (2-way valve) and open the valve by turning the wrench in a 1/4 counterclockwise turn. Wait and listen for gas potentially exiting the system, then close the valve after 5 seconds.&#xA0;<img src="https://attachments.gorgias.help/Q9r0k7BYaV2vg13y/hc/9JWjXVxG8m6DvMqm/2025120415-3571cbda-89b1-484a-b2f9-ea0a2c718c8c-wyt17_air_evacuation_steps11.png" style="width: 400px;" class="fr-fic fr-dib fr-bordered"><ul><li><strong>Notes:&#xA0;</strong><ul><li>When opening valve stems, turn the supplied Allen wrench until the valve stem comes into contact with the stopper. Do not try to force the valve to open further.</li><li>Do not open either of these valves until the evacuation steps are completed and the system is ready for startup.&#xA0;</li></ul></li></ul></li><li>Watch the pressure gauge for a few minutes to make sure that there is no drop in pressure. The pressure gauge should now show higher than the atmospheric pressure.&#xA0;</li><li>Remove the charge hose from the service port.</li><li>Use a hexagonal wrench to fully open both the high pressure and low pressure valves counterclockwise.<img src="https://attachments.gorgias.help/Q9r0k7BYaV2vg13y/hc/9JWjXVxG8m6DvMqm/2025120415-25e50631-8526-4323-a1c6-7d1eac456d3a-wyt17_air_evacuation_step14.png" style="width: 400px;" class="fr-fic fr-dib fr-bordered"></li><li>Tighten valve caps on all three valves (service port, high pressure, low pressure) by hand. Do not torque down further.<img src="https://attachments.gorgias.help/Q9r0k7BYaV2vg13y/hc/9JWjXVxG8m6DvMqm/2025120415-1e70c1c7-b2fa-42ef-a1f7-e97088c0a10e-wyt17_air_evacuation_step15.png" style="width: 400px;" class="fr-fic fr-dib fr-bordered"></li></ol>

Air Evacuation & Bleeding the Circuit

This article explains how to connect the power/signal electrical wiring to outdoor units.

<h2 id="introduction"><u>Introduction</u></h2><p>This article explains how to connect the power/signal electrical wiring to outdoor units.&#xA0;</p><p>A comprehensive wiring diagram is printed on the inside of the wiring cover.&#xA0;<img src="https://attachments.gorgias.help/Q9r0k7BYaV2vg13y/hc/9JWjXVxG8m6DvMqm/2025120320-fee6f847-17b7-41fa-a74f-706d9fa0a44d-wyt17_odu_electrical_wiring.png" style="width: 500px;" class="fr-fic fr-dib fr-bordered"></p><p>This article is for the following articles:</p><ul id="isPasted"><li id="isPasted"><a href="https://www.pioneerminisplit.com/collections/diamante-essenza-high-wall-series" target="_blank" rel="noopener noreferrer">Diamante Essenza (WYT-17)</a></li><li><a href="https://www.pioneerminisplit.com/collections/diamante-pro-high-wall-series" target="_blank" rel="noopener noreferrer">Diamante Pro (WYT-20)</a></li><li><a href="https://www.pioneerminisplit.com/collections/quantum-ultra-high-wall-series" target="_blank" rel="noopener noreferrer">Quantum Ultra (WYT-24)</a></li><li><a href="https://www.pioneerminisplit.com/collections/quantum-hyperformance-high-wall-series" target="_blank" rel="noopener noreferrer">Quantum Hyperformance (WYT-25)</a></li><li><a href="https://www.pioneerminisplit.com/collections/quantum-fresh-series-breathe-the-difference" target="_blank" rel="noopener noreferrer">Quantum Fresh (WYT-FA)</a></li><li><a href="https://www.pioneerminisplit.com/collections/quantum-ultra-ceiling-cassette" target="_blank" rel="noopener noreferrer">Quantum Ultra Ceiling Cassette (CYT-24)</a></li><li><a href="https://www.pioneerminisplit.com/collections/quantum-ultra-ducted-ceiling-concealed" target="_blank" rel="noopener noreferrer">Quantum Ultra Ducted Ceiling Concealed (RYT-24)</a></li><li><a href="https://www.pioneerminisplit.com/collections/quantum-ultra-universal-flex-series" target="_blank" rel="noopener noreferrer">Quantum Ultra Floor-Ceiling Flex (UYT-24)</a></li></ul><h2 id="isPasted"><u>Connect the Signal Cable</u></h2><p>The indoor and outdoor units each have three terminals (1, 2, 3) and ground wiring (G). Match the terminals number to number. Color selection does not matter as much as matching number to number does.&#xA0;<img src="https://attachments.gorgias.help/Q9r0k7BYaV2vg13y/hc/9JWjXVxG8m6DvMqm/2025120218-43815c26-9bed-46ff-aead-29633f2eeab1-wytfa_connect_signal_cable.png" style="width: 300px;" class="fr-fic fr-bordered fr-dib"></p><p>Do not mix up the wires between each ends. &#xA0;</p><p>Consult the diagrams affixed to the indoor and outdoor units respectively for specific wiring instructions.&#xA0;</p><h2 id="steps"><u>Steps</u></h2><ol><li>Unscrew and remove the handle on the right side plate of the outdoor unit.&#xA0;</li><li>Wire the system using the appropriate gauge wire and the wiring diagram found on the handle cover. For information on the appropriate gauge wire to use, click <a href="https://help.pioneerminisplit.com/en-US/articles/cable-wire-specifications-352513" target="_blank" rel="noopener noreferrer">here</a>.&#xA0;</li><li>Use a proper flexible rain-tight conduit with appropriate size connectors.&#xA0;</li><li>Fasten the power connection wires into place using the supplied wire clamps.&#xA0;</li><li>Check the wiring against the diagram to ensure that it is wired correctly. A proper ground connection must be established.&#xA0;</li><li>Rescrew and reinstall the cover handle.&#xA0;</li></ol>

Connect the Power/Signal Electrical Wiring to Outdoor Units

This article explains how to connect the refrigerant piping to the outdoor unit.

Connect the Refrigerant Piping to the Outdoor Unit

This article explains how to mount outdoor units.

Mount the Outdoor Unit

This article explains how to select the installation location for outdoor units.

<h2 id="isPasted"><u>Introduction</u></h2><p>This article explains how to select the installation location for outdoor units.&#xA0;</p><p>This article is for the following systems:&#xA0;</p><ul><li id="isPasted"><a href="https://www.pioneerminisplit.com/collections/diamante-essenza-high-wall-series" target="_blank" rel="noopener noreferrer">Diamante Essenza (WYT-17)</a></li><li><a href="https://www.pioneerminisplit.com/collections/diamante-pro-high-wall-series" target="_blank" rel="noopener noreferrer">Diamante Pro (WYT-20)</a></li><li><a href="https://www.pioneerminisplit.com/collections/quantum-ultra-high-wall-series" target="_blank" rel="noopener noreferrer">Quantum Ultra (WYT-24)</a></li><li><a href="https://www.pioneerminisplit.com/collections/quantum-hyperformance-high-wall-series" target="_blank" rel="noopener noreferrer">Quantum Hyperformance (WYT-25)</a></li><li><a href="https://www.pioneerminisplit.com/collections/quantum-fresh-series-breathe-the-difference" target="_blank" rel="noopener noreferrer">Quantum Fresh (WYT-FA)</a></li><li><a href="https://www.pioneerminisplit.com/collections/quantum-ultra-ceiling-cassette" target="_blank" rel="noopener noreferrer">Quantum Ultra Ceiling Cassette (CYT-24)</a></li><li><a href="https://www.pioneerminisplit.com/collections/quantum-ultra-ducted-ceiling-concealed" target="_blank" rel="noopener noreferrer">Quantum Ultra Ducted Ceiling Concealed (RYT-24)</a></li><li><a href="https://www.pioneerminisplit.com/collections/quantum-ultra-universal-flex-series" target="_blank" rel="noopener noreferrer">Quantum Ultra Floor-Ceiling Flex (UYT-24)</a></li></ul><h2 id="select-the-location"><u>Select the Location</u></h2><p>Follow the tolerances depicted in the illustration below:&#xA0;</p><p><img src="https://attachments.gorgias.help/Q9r0k7BYaV2vg13y/hc/9JWjXVxG8m6DvMqm/2025120319-1859db3e-5ecd-48e9-8bdd-faf41444ae78-wyt17_odu_installation_requirements.png" style="width: 500px;" class="fr-fic fr-dib fr-bordered"></p><p>Follow these best practices for selecting an optimal space for installing the outdoor unit:&#xA0;</p><ul><li>Do not install the unit near sources of heat, steam, or flammable gases.&#xA0;</li><li>Do not install the system in areas prone to extreme winds or dust.&#xA0;</li><li>Do not install the unit in an area that has many individuals pass by.&#xA0;</li><li>Select a location where the air discharge and operating sound level will not disturb others.&#xA0;</li><li>Install the system in a shaded area or utilize cover/sun protection that will not interfere with air flow. This will also protect the system from heavy rain or snow.&#xA0;</li><li>Install the unit in a safe and sturdy location.&#xA0;</li><li>Install rubber vibration absorbers if the system can induce vibrations in any structure.&#xA0;</li><li><strong>If the unit is exposed to heavy win</strong><strong>d:&#xA0;</strong>Install the unit so that the air outlet fan is at a 90&#xB0; angle to the direction of the wind. If needed, use wind baffles or build a barrier in front of, but sufficiently away from, the unit to protect it from extremely heavy winds.&#xA0;</li><li><strong>If the unit is frequently exposed to heavy rain or snow:&#xA0;</strong>Build a shelter above the unit to protect it from the rain or snow. Be careful not to obstruct the air flow around the unit.&#xA0;</li><li><strong>If the unit is frequently exposed to salty air (seaside air):</strong> Use specifically approved anti-corrosion coating sprays on the heat exchanger surface in order to resist corrosion.&#xA0;</li></ul>

Select the Installation Location for Outdoor Units

This article explains how to select the ideal installation location for the outdoor unit of Vertex Ducted Central Split (DYC-18) systems.

<h2 id="introduction"><u>Introduction</u></h2><p>This article explains how to select the ideal installation location for the outdoor unit of <a href="https://www.pioneerminisplit.com/collections/vertex-ducted-central-split" target="_blank" rel="noopener noreferrer">Vertex Ducted Central Split (DYC-18) systems</a>.&#xA0;</p><h2 id="unit-dimensions"><u>Unit Dimensions</u></h2><table style="width: 100%;"><tbody><tr><td style="width: 38.3095%; text-align: center; background-color: rgb(239, 239, 239);" class="fr-thick"><strong>Unit Size</strong></td><td style="width: 61.404%; text-align: center; background-color: rgb(239, 239, 239);" class="fr-thick"><strong>W x D x H</strong></td></tr><tr><td style="width: 38.3095%; text-align: center;" class="fr-thick">24K/36K</td><td style="width: 61.404%; text-align: center;" class="fr-thick">29-1/2&quot; x 29-1/2&quot; x 25&quot; inches (749 x 749 x 635 mm)</td></tr><tr><td style="width: 38.3095%; text-align: center;" class="fr-thick">48K/56K</td><td style="width: 61.404%; text-align: center;" class="fr-thick">29-1/2&quot; x 29-1/2&quot; x 32-7/8&quot; inches (749 x 749 x 835 mm)</td></tr></tbody></table><h2 id><img src="https://attachments.gorgias.help/Q9r0k7BYaV2vg13y/hc/9JWjXVxG8m6DvMqm/2026012319-84b939d1-6cc1-4152-82d1-e64b961720fb-dyc18_wdh.png" style="width: 600px;" class="fr-fic fr-dib fr-bordered">&#xA0;</h2><h2 id="installation-precautions--restrictions"><u>Installation Precautions &amp; Restrictions</u></h2><p><strong>Position Restrictions</strong></p><ul><li>Make sure that the discharge area is unrestricted. At least 5 feet (1.5 m) above the top of the unit.&#xA0;</li><li>Do not position the outdoor unit near bedrooms, as the normal operating sound could be audible.<img src="https://attachments.gorgias.help/Q9r0k7BYaV2vg13y/hc/9JWjXVxG8m6DvMqm/2026012320-2d539979-0e73-449b-a131-3e703adf7582-dyc18_odu_installation_shrubs.png" style="width: 500px;" class="fr-fic fr-dib fr-bordered"></li><li>Position the system in a way that leaves enough space for smooth airflow, wiring, refrigerant lines, and maintenance.&#xA0;</li><li>Ensure there a minimum clearance of 12 inches (305 mm) on one side of the control board access panel, as well as a minimum clearance of 24 inches (610 mm) on the adjacent side of the control board access panel.&#xA0;</li><li>Maintain a distance of 24 inches (610 mm) between the adjacent units.&#xA0;</li><li>Make sure that lawn sprinklers, hoses, and waste water cannot spray directly on the outer panel of the unit for long periods of time.&#xA0;</li><li>In coastal areas, install the unit on the side away from the waterfront.&#xA0;</li><li>Avoid installing the unit in a location that is exposed to corrosive environments. This may shorten the service life of the unit, corrode metal parts, and negatively impact the performance of the unit. The following are examples of corrosive elements to avoid:&#xA0;<ul><li>Chloride</li><li id="isPasted">Chlorine</li><li id="isPasted">Compounds commonly found near seawater</li><li id="isPasted">Fertilizers</li><li id="isPasted">Fluorine</li><li>Sodium</li><li>Sodium hydroxide</li><li>Sodium sulfate</li><li>Sulfur</li><li>Various chemical pollutants from industrial or manufacturing plants</li></ul></li></ul><p><strong>Cold Climates</strong></p><ul><li>Select a location where water, snow, or ice cannot fall directly on the system from the roof or overhangs. Precautions must be taken for units installed in areas with snow and long-term temperatures below the freezing point.&#xA0;<img src="https://attachments.gorgias.help/Q9r0k7BYaV2vg13y/hc/9JWjXVxG8m6DvMqm/2026012320-90415015-3a99-42a4-bf2f-d926ddc2ee83-dyc18_odu_installation_water.png" style="width: 500px;" class="fr-fic fr-dib fr-bordered"></li><li>In snowy areas, raise the unit by 3-12 inches (76-305 mm). This extra height will allow the snow and ice that melts during defrosting cycles to discharge before freezing. Ensure that the drain hole on the unit chassis is not blocked, otherwise it might limit the defrosting water discharge.&#xA0;</li><li>If possible, avoid locations that are prone to snow. If this not possible, install a snow barrier around the unit to prevent snow from accumulating on the side of the unit.&#xA0;<br id="isPasted"><img src="https://attachments.gorgias.help/Q9r0k7BYaV2vg13y/hc/9JWjXVxG8m6DvMqm/2026012320-0bceb4af-78b4-4c02-a894-83c8c9ccaf3a-68e57303-5c89-4a29-a514-4f6562eac8d8.png" class="fr-fic fr-dib fr-bordered" style="width: 500px;"></li></ul><p><strong>Restrictions for Refrigerant Pipelines</strong></p><table style="width: 100%;"><tbody><tr><td style="width: 33.189%; text-align: center; background-color: rgb(239, 239, 239);" class="fr-thick" colspan="2" rowspan="2"><strong>Refrigerant Line</strong></td><td style="width: 66.3781%; text-align: center; background-color: rgb(239, 239, 239);" colspan="4" class="fr-thick"><strong>Capacity (Kbtu/h)</strong></td></tr><tr><td style="width: 16.6667%; text-align: center; background-color: rgb(239, 239, 239);" class="fr-thick"><strong>24K</strong></td><td style="width: 16.6667%; text-align: center; background-color: rgb(239, 239, 239);" class="fr-thick"><strong>36K</strong></td><td style="width: 16.6667%; text-align: center; background-color: rgb(239, 239, 239);" class="fr-thick"><strong>48K</strong></td><td style="width: 16.6667%; text-align: center; background-color: rgb(239, 239, 239);" class="fr-thick"><strong>56K</strong></td></tr><tr><td style="width: 16.6667%; text-align: center;" class="fr-thick">Liquid Suction</td><td style="width: 16.6667%; text-align: center;" class="fr-thick">inches</td><td style="width: 16.6667%; text-align: center;" class="fr-thick">3/8-3/4</td><td style="width: 16.6667%; text-align: center;" class="fr-thick">3/8-3/4</td><td style="width: 16.6667%; text-align: center;" class="fr-thick">3/8-7/8</td><td style="width: 16.6667%; text-align: center;" class="fr-thick">3/8-7/8</td></tr><tr><td style="width: 16.6667%; text-align: center;" class="fr-thick">Max. Refrigerant</td><td style="width: 16.5945%; text-align: center;" class="fr-thick" rowspan="2">feet</td><td style="width: 66.3781%; text-align: center;" class="fr-thick" colspan="4" rowspan="2">100</td></tr><tr><td style="width: 16.6667%; text-align: center;" class="fr-thick">Line Length*</td></tr><tr><td style="width: 16.6667%; text-align: center;" class="fr-thick">Max. Elevation*</td><td style="width: 16.5945%; text-align: center;" class="fr-thick" rowspan="2">feet</td><td style="width: 66.3781%; text-align: center;" class="fr-thick" colspan="4" rowspan="2">50</td></tr><tr><td style="width: 16.6667%; text-align: center;" class="fr-thick">Vertical Lift*</td></tr></tbody></table><p>*It is recommended to adopt standard pipeline sizes.&#xA0;</p><ul><li>Maximum equivalent length of the pipeline = 100 feet (30.5 m)<img src="https://attachments.gorgias.help/Q9r0k7BYaV2vg13y/hc/9JWjXVxG8m6DvMqm/2026012320-b28a99dd-deed-4ec9-a40c-86704dd4d3a7-08c8fbc1-789d-42b8-a729-ce4041e25863.png" id="isPasted" class="fr-fic fr-dib fr-bordered" style="width: 500px;"></li><li>Maximum vertical equivalent length = 50 feet (15 m).&#xA0;<br id="isPasted"><img src="https://attachments.gorgias.help/Q9r0k7BYaV2vg13y/hc/9JWjXVxG8m6DvMqm/2026012320-9413873b-b0bd-4df1-9711-fdbc81e8d496-daccc826-ad8c-4e18-a8c7-503ee9bb60f0.png" class="fr-fic fr-dib fr-bordered" style="width: 500px;"><br id="isPasted"><img src="https://attachments.gorgias.help/Q9r0k7BYaV2vg13y/hc/9JWjXVxG8m6DvMqm/2026012320-2d5c387e-38eb-488b-9e19-c31d8ea39aee-62d17446-843d-4963-9790-b9027e2b9dfd.png" class="fr-fic fr-dib fr-bordered" style="width: 500px;"></li><li>If the suction line exceeds 65 feet (20 m), do not use a suction line larger than recommended.&#xA0;</li></ul><p><strong>Long Line Installation Precautions</strong></p><ul><li>The length of the connecting line from the outdoor unit to the indoor unit cannot exceed 100 feet (30.5 m).&#xA0;</li><li>If all the long lines are in a horizontal position, no additional measures are required.&#xA0;</li><li>If there is a vertical height difference in the long lines, install them according to the following requirements:<ul><li>When the vertical height difference of the indoor and outdoor units is less than 16.5 feet (5 m), no additional measurements are required.&#xA0;</li><li>When the vertical height difference is more than 16.5 feet (5) but less than 33 feet (10 m), add an oil return trap in the middle of the height difference.&#xA0;<img src="https://attachments.gorgias.help/Q9r0k7BYaV2vg13y/hc/9JWjXVxG8m6DvMqm/2026012320-bc7f69a8-c2bb-411a-8275-9410ce4e452f-image%20(1).png" style="width: 400px;" class="fr-fic fr-dib fr-bordered"></li><li>When the vertical height difference is more than 33 feet (10 m) but less than 50 feet (15 m), add two oil return traps at an equal distance in the height difference. &#xA0;</li><li>The vertical height difference between the indoor and outdoor units cannot exceed 50 feet (15 m). The following is the connection method of the oil return trap:<img src="https://attachments.gorgias.help/Q9r0k7BYaV2vg13y/hc/9JWjXVxG8m6DvMqm/2026012319-640b8663-0106-45db-8943-ca5c6f1d8c08-dyc18_odu_oil_trap_structure.png" style="width: 500px;" class="fr-fic fr-dib fr-bordered"></li></ul></li></ul><h2 id="isPasted"><u>Installation Notes</u></h2><ul><li>Fences or shrubs can provide additional shielding protection for the unit. Be sure to maintain the minimum clearances for the unit.&#xA0;</li><li>When installing the outdoor unit on the roof, ensure that the roof can support the weight of the unit. Choose an appropriate isolation position to prevent sound or vibration from being transmitted to the building structure.</li></ul>

Select the Outdoor Unit Installation Location for Vertex Ducted Central Split (DYC-18) Systems

This article explains how to set up the condensate water drainage for outdoor units.

<h2 id="introduction"><u>Introduction</u></h2><p>This article explains how to set up the condensate water drainage for outdoor units.&#xA0;</p><p>Use the drain joint and drainpipe included with the system to direct away the condensate water and ice formed in the outdoor unit during Heating mode.</p><p>This is optional and only needed if the default configuration of the water drainage out from the port on the bottom side is not desired.&#xA0;</p><p id="isPasted">This article is for the following systems:&#xA0;</p><ul><li id="isPasted"><a href="https://www.pioneerminisplit.com/collections/diamante-essenza-high-wall-series" target="_blank" rel="noopener noreferrer">Diamante Essenza (WYT-17)</a></li><li><a href="https://www.pioneerminisplit.com/collections/diamante-pro-high-wall-series" target="_blank" rel="noopener noreferrer">Diamante Pro (WYT-20)</a></li><li><a href="https://www.pioneerminisplit.com/collections/quantum-ultra-high-wall-series" target="_blank" rel="noopener noreferrer">Quantum Ultra (WYT-24)</a></li><li><a href="https://www.pioneerminisplit.com/collections/quantum-hyperformance-high-wall-series" target="_blank" rel="noopener noreferrer">Quantum Hyperformance (WYT-25)</a></li><li><a href="https://www.pioneerminisplit.com/collections/quantum-fresh-series-breathe-the-difference" target="_blank" rel="noopener noreferrer">Quantum Fresh (WYT-FA)</a></li><li><a href="https://www.pioneerminisplit.com/collections/quantum-ultra-ceiling-cassette" target="_blank" rel="noopener noreferrer">Quantum Ultra Ceiling Cassette (CYT-24)</a></li><li><a href="https://www.pioneerminisplit.com/collections/quantum-ultra-ducted-ceiling-concealed" target="_blank" rel="noopener noreferrer">Quantum Ultra Ducted Ceiling Concealed (RYT-24)</a></li><li><a href="https://www.pioneerminisplit.com/collections/quantum-ultra-universal-flex-series" target="_blank" rel="noopener noreferrer">Quantum Ultra Floor-Ceiling Flex (UYT-24)</a></li></ul><h2 id="steps"><u>Steps</u></h2><ol><li>Fasten the drain port in the 1 inch (25 mm) port located in the part of the unit shown in the illustration.&#xA0;<img src="https://attachments.gorgias.help/Q9r0k7BYaV2vg13y/hc/9JWjXVxG8m6DvMqm/2025120320-a02905f0-7848-4a41-a7af-367f6bc7c51b-wyt17_odu_condensate_water_drainage.png" style="width: 500px;" class="fr-fic fr-dib fr-bordered"></li><li>Connect the drain port and drainpipe.&#xA0;</li><li>Ensure that the condensate will drain to a suitable place.&#xA0;</li></ol>

Set Up the Condensate Water Drainage for Outdoor Units

This article explains to properly install outdoor units on pads for Vertex Ducted Central Split (DYC-18) systems.

<p>This article explains how to properly install outdoor units on pads for <a href="https://www.pioneerminisplit.com/collections/vertex-ducted-central-split" target="_blank" rel="noopener noreferrer">Vertex Ducted Central Split (DYC-18) systems</a>.&#xA0;</p><p>Consider the following:</p><ul><li>All sides of the pad must be at least 1-2 inches (25-51 mm) larger than the unit.</li><li>The pad must be separate from any structure.&#xA0;</li><li>The pad must be level.&#xA0;</li><li>Ensure that the pad is high enough above the ground for proper drainage.&#xA0;</li><li>The location of the pad must comply with national, state, and local regulations.&#xA0;</li></ul><p><img src="https://attachments.gorgias.help/Q9r0k7BYaV2vg13y/hc/9JWjXVxG8m6DvMqm/2026012320-8a613751-d802-46df-b3ed-bed975ca63e8-dyc18_odu_installation_support_pads.png" style="width: 500px;" class="fr-fic fr-dib fr-bordered"></p>

Understand how to Install Outdoor Units on Support Pads for Vertex Ducted Central Split (DYC-18) Systems

Chat with one of our friendly reps to get help quick.

Something on your mind not found here? E-mail us.

We offer phone support if you don't want to type.

Support Center

Outdoor Units (Installation & Setup)

Installation & Setup

Ductless & Ducted Systems (Installation & Setup)

Pioneer Offers Hyper-Heat Units

Pioneer Systems Offer Both Heating & Cooling Functions

Understand the Difference Between 115V & 230V Systems

Understand the Refrigerants Used for Each Model

How to Choose a System

Mini Splits are Capable of Using Fewer Indoor Units than the Outdoor Unit’s Zonal Capacity

Pioneer Mini Splits Function as Dehumidifiers

Pioneer Offers Different Lineset Lengths

Pioneer Offers Pre-Charged Linesets

Pioneer Offers Pre-Flared Linesets

Pioneer Systems Include Factory Pre-Charged Refrigerant

Single-Zone Mini Splits Cannot be Used with Multiple Indoor Units

Understand the Life Expectancy of Pioneer Systems

Understand how Mini Splits are Powered

Mini-Split Basics

Determine the Unit Size Needed for Your Space

Match the Lineset Diameter to Your Pioneer Indoor Unit

Understand Why Short Cycling Occurs When Sizing Systems

Sizing & Efficiency Guide

Start Here

Understand the Differences Between Inverter+ & Inverter++ Systems

Understand the Differences Between the Wall-Mounted Ductless Mini Splits

Understand Which Units are Rated Energy-Star

Compare Models

Learn About the Discounts Available

Learn About the Energy-Star Tax Credits Available for Pioneer Systems

Learn More about IRA Tax Credits

Learn Why Your Pioneer Discount Code Only Says "SAMPLE"

Redeem Your Pioneer Rewards Points When Shopping Online

Understand How to Manage Multiple Credit Card Charges with Pioneer

Financing & Payment

Learn About Our Shipping & Delivery Details

Understand the Qualifications for Free Shipping

Order Status & Shipping

Diamante Essenza High-Wall (WYT-17) Overview

Diamante Pro High-Wall (WYT-20) Overview

Quantum Fresh High-Wall (WYT-FA) Overview

Quantum Hyperformance High-Wall (WYT-25) Overview

Quantum Ultra Ceiling Cassette (CYT-24) Overview

Quantum Ultra Ducted Ceiling Concealed (RYT-24) Overview

Quantum Ultra Floor-Ceiling Flex (UYT-24) Overview

Quantum Ultra High-Wall (WYT-24) Overview

Quantum Ultra Multi-Zone Overview

Vertex Ducted Central Split (DYC-18) Overview

Ducted & Ductless Systems (Product Line Overviews)

ECOasis 50 Ductless Wall-Mounted Single-Room Energy Recovery Ventilator (ERV) Overview

ECOasis 150 Ductless Wall-Mounted Single-Room Energy Recovery Ventilator (ERV) Overview

Energy Recovery Ventilators (Product Line Overviews)

QHD070 Whole-House Ducted Dehumidifier (QHD) Overview

High Performance Dehumidifier (Product Line Overviews)

Full Inverter Rooftop RV Air Conditioner Heat Pump (PYZ) Overview

Under-Bench RV Inverter Packaged Heat Pump Air Conditioner (PYR) Overview

Recreational Vehicle Systems (Product Line Overviews)

Product Line Overviews

Find Out How to Complete Returns

Figure Out How to Start Your Return

Learn About Our Policy for Undeliverable or Refused Shipments

Learn About Our Return Policy

Understand How to Return an Item

Understand the Eligibility Requirements for Refunds

Understand Our Return Fees

Understand Our Return Process

Returns & Refunds

Shopping & Pre-Purchase

Find an Installer for Your System

Find Professionals to Install Your Pioneer System

Learn Who is Permitted to Install Your System

Understand if Our Systems can be Self-Installed

Understand the Cost & Time Spent on Installing Systems

First-Time Setup

Connect the Drain Hose for LCAC Systems

Connect the Refrigerant Piping to the Indoor Unit

Cassette Units

Ducted Units

Flex Units

Wall-Mounted Units

Indoor Units (Installation & Setup)

Angle Linesets Upward

Complete the Safety Checks & Test Run

Find Out if a Wall-Mounted Indoor Unit can be Set onto Ceilings

Find Out if the Indoor Unit Requires Anything Extra in Order to be Wall-Mounted

Find Out the Ideal Height for Mounting Indoor Units

Leakage Inspection & Vacuuming for Refrigerant Lines

Learn the Gauge of Wire Used for Ductless System Connections

Open the Service Valve

Setup the Lineset to Exit from the Side of the Indoor Unit

Understand 6-Foot Plastic Whips & 4-Lead Mini Split Connection Wire

Understand how to Properly Uncoil the Lineset

Understand the Drilling Details to Accommodate Drain & Refrigerant Lines

Understand the Requirements for Installing Your System

Understand the Torque Wrench Size for Installing Your System

Installation Requirements (Installation & Setup)

Understand the Meaning of “Multi-Zone”

Multi-Zone Units (Installation & Setup)

Install ECOasis 50 Energy Recovery Ventilators

Install ECOasis 150 Energy Recover Ventilators

Energy Recovery Ventilator (Installation & Setup)

Connect the Drain Fitting for QHD070 Whole-House Ducted Dehumidifiers

High Performance Dehumidifiers (Installation & Setup)

Install Rooftop RV Systems: Getting Started

Create the Roof Opening for Rooftop RV Systems

Install the Air Duct & Top Mounting Plate for Rooftop RV Systems

Mount the Panel for Rooftop RV Systems

Place the Unit onto the Roof for Rooftop RV Systems

Setup the Electrical Wiring for Rooftop RV Systems

Setup the System Connections for Rooftop RV Systems

Understand the Installation Requirements for Rooftop RV Systems

Rooftop RV Inverter (Installation & Setup)

Install Under-Bench RV Systems: Getting Started

Connect & Power Up Under-Bench RV Systems

Create the Floor Openings for Under-Bench RV Systems

Create the Recirculation Air Opening for Under-Bench RV Systems

Fasten the Under-Bench RV System into Place

Install the Wall Thermostat for Under-Bench RV Systems

Understand the Ductwork Best Practices for Under-Bench RV Systems

Understand the Installation Requirements for Under-Bench RV Systems

Under-Bench RV Inverter (Installation & Setup)

Recreational Vehicle Systems (Installation & Setup)

Understand the DIP Switches for Vertex Ducted Central Split (DYC-18) Systems

DIP Switch Layouts

Turn the LED Display On or Off

Understand the Display Board for Quantum Ultra Ducted Ceiling Concealed (RYT-24) Systems

Understand the Display Panel for RV Rooftop Systems

Understand the Front Panel Displays for Quantum Ultra Ceiling Cassette (CYT-24) Systems

Understand the Front Panel Display for Quantum Ultra Floor-Ceiling Flex (UYT-24) Systems

Understand the Front Panel Display for Wall-Mounted Systems

Understand the Master Unit Display for ECOasis 50 Energy Recovery Ventilators

Understand the Onboard Controller & Terminal Block Layout for QHD070 Whole-House Ducted Dehumidifiers

Understand the Wall Controller Display for RV Under-Bench Systems

Display Layouts

CL error code

Clean the Anti-Dust Filters for Diamante Essenza & Pro Systems

Clean the Anti-Dust Filters for Quantum Fresh Systems

Cleaning the Anti-Dust Filters for Quantum Ultra Ceiling Cassette Systems

Clean the Anti-Dust Filters for Quantum Ultra Ducted Ceiling Concealed Systems

Clean the Anti-Dust Filters for Quantum Ultra Floor-Ceiling Flex Systems

Clean the Anti-Dust Filters for Quantum Ultra High Wall-Mount & Hyperformance Systems