This article provides an overview of the installation process for UYB-20 floor-ceiling flex systems.

<h2 id="isPasted"><u>Introduction</u></h2><p>This article provides an overview of the installation process for UYB-20 floor-ceiling flex systems.&#xA0;</p><p>Each section in this article represents a step in the installation process. Click the link in each section to learn about that specific step.&#xA0;</p><p><strong>Note:</strong> Before beginning the installation, refer to the label on the product box to ensure the model number of the indoor unit matches the model number of the outdoor unit.&#xA0;</p><h2 id="1-select-the-installation-location-for-the-indoor--outdoor-units"><u>1. Select the Installation Location for the Indoor &amp; Outdoor Units</u></h2><p>We recommend understanding the criteria for selecting ideal locations for the indoor and outdoor units.&#xA0;</p><ul><li style="font-size: 16px;">The guidelines for selecting ideal installation locations for the indoor and outdoor units can be found in this article.&#xA0;</li></ul><h2 id="2-install-the-indoor-unit"><u>2. Install the Indoor Unit</u></h2><p>Begin the installation by hanging the indoor unit. Then, connect the ducting, install the filter, and drill the wall hole for the piping.</p><ul><li style="font-size: 16px;">For information on hanging the indoor unit, click this link.&#xA0;</li><li style="font-size: 16px;">Read this article for information on installing the air conduit installation plate.&#xA0;</li><li style="font-size: 16px;">Learn more about drilling the wall hole for the piping by reading this article.&#xA0;</li></ul><h2 id="3-connect-the-drainpipe"><u>3. Connect the Drainpipe</u></h2><p>Attach the drainpipe to direct water away from the unit. Improper installation may cause unit and property damage.&#xA0;</p><ul><li style="font-size: 16px;"><span style="font-size: 16px;">Click this&#xA0;</span><span style="font-size: 16px;">link</span><span style="font-size: 16px;">&#xA0;to learn how to connect the drainpipe.</span>&#xA0;</li></ul><h2 id="4-install-the-outdoor-unit"><u>4. Install the Outdoor Unit</u></h2><p>Next, install the drain joint for the outdoor unit, then mount the unit to the ground or a wall-mounted bracket.&#xA0;</p><ul><li style="font-size: 16px;">For information on installing the drain joint for the outdoor unit, click this link.&#xA0;</li><li style="font-size: 16px;">Read this article to learn about mounting the outdoor unit.&#xA0;</li></ul><h2 id="5-connect-the-refrigerant-pipes"><u>5. Connect the Refrigerant Pipes</u></h2><p>Once the indoor and outdoor units are installed, connect the refrigerant pipes.&#xA0;</p><ul><li style="font-size: 16px;">Click this article for information on connecting the refrigerant pipes.&#xA0;</li></ul><h2 id="6-connect-the-electrical-wires"><u>6. Connect the Electrical Wires</u></h2><p>Connect the electrical wires for the system, starting with the outdoor wires followed by the indoor wires.&#xA0;</p><ul><li style="font-size: 16px;">Get information on connecting the wires by clicking this link.</li></ul><h2 id="7-evacuate-the-refrigerant-circuit"><u>7. Evacuate the Refrigerant Circuit</u></h2><p>Use a vacuum pump and manifold gauge to evacuate the refrigerant circuit, removing any non-condensable gas and moisture from the system.</p><h2 id="8-perform-a-test-run"><u>8. Perform a Test Run</u></h2><p>Perform the test run after the entire system has been completely installed. Failure to perform the test run may result in unit damage, property damage, or personal injury.</p><ul><li style="font-size: 16px;">For instructions on performing a test run, read this <a href="https://help.pioneerminisplit.com/en-US/install-test-run-3672815" target="_blank" rel="noopener noreferrer">article</a>.</li></ul>

Install UYB-20 Floor-Ceiling Flex Systems: Getting Started

This article outlines the criteria for selecting the installation sites for UYB-20 floor-ceiling flex indoor and outdoor units.

<h2 id="isPasted"><u>Introduction</u></h2><p>This article outlines the criteria for selecting the installation sites for UYB-20 floor-ceiling flex indoor and outdoor units.&#xA0;</p><p>Before starting, refer to the label on the product box to make sure that the model number of the indoor unit matches the model number of the outdoor unit.&#xA0;</p><p>We recommend understanding the guidelines for selecting ideal locations for the indoor and outdoor units. The following are standards intended to help select appropriate locations for the units. &#xA0;</p><h2 id="indoor-unit"><u>Indoor Unit</u></h2><p><strong>Proper installation locations for the indoor unit must ensure the following standards:&#xA0;</strong></p><ul><li style="font-size: 16px;">Sufficient space for installation and maintenance.&#xA0;</li><li style="font-size: 16px;">Sufficient space to connect the pipes and drainpipe.&#xA0;</li><li style="font-size: 16px;">No direct radiation from heaters.&#xA0;</li><li style="font-size: 16px;">The air inlet and outlet are not blocked.&#xA0;</li><li style="font-size: 16px;">The airflow can fill the entire room.&#xA0;</li><li style="font-size: 16px;">The ceiling is horizontal and its structure can sustain the indoor unit&apos;s weight.&#xA0;</li></ul><p><strong>Do not install the indoor unit in the following locations:&#xA0;</strong></p><ul><li style="font-size: 16px;">Areas with oil drilling or fracking.&#xA0;</li><li style="font-size: 16px;">Coastal areas with high salt content in the air.&#xA0;</li><li style="font-size: 16px;">Areas with caustic gases in the air, such as near hot springs.&#xA0;</li><li style="font-size: 16px;">Areas that experience power fluctuations, such as factories.&#xA0;</li><li style="font-size: 16px;">Enclosed spaces, such as cabinets.&#xA0;</li><li style="font-size: 16px;">Kitchens that use natural gas.&#xA0;</li><li style="font-size: 16px;">Areas with strong electromagnetic waves.&#xA0;</li><li style="font-size: 16px;">Areas that store flammable materials or gas.&#xA0;</li><li style="font-size: 16px;">Rooms with high humidity, such as bathrooms or laundry rooms.&#xA0;</li></ul><p><strong>Recommended distance between the mounted indoor unit:<img src="https://attachments.gorgias.help/Q9r0k7BYaV2vg13y/hc/9JWjXVxG8m6DvMqm/2026050619-64c43467-c8d2-4416-a7b1-f2f162ccc143-uyb_distance_specs.png" style="width: 600px;" class="fr-fic fr-dib fr-bordered"></strong></p><h2 id="outdoor-unit"><u>Outdoor Unit</u></h2><p><strong>Proper installation locations for the outdoor unit must ensure the following standards:&#xA0;</strong></p><ul><li style="font-size: 16px;">The installation&apos;s spatial requirements shown in the illustration are met.<img src="https://attachments.gorgias.help/Q9r0k7BYaV2vg13y/hc/9JWjXVxG8m6DvMqm/2026042112-97d87069-8741-4b72-8fcc-bd73b71ee516-cyb20_odu_spatial_requirements.png" style="width: 500px;" class="fr-fic fr-dib fr-bordered"></li><li style="font-size: 16px;">The location is solid enough to support the unit and prevent vibration.</li><li style="font-size: 16px;">Sufficient air circulation and ventilation.&#xA0;</li><li style="font-size: 16px;">Noise from the unit will not disturb other people.&#xA0;</li><li style="font-size: 16px;">The location is protected against prolonged exposure to direct sunlight or precipitation.&#xA0;</li><li style="font-size: 16px;">The location is protected against ice buildup and coil damage during snowfall.&#xA0;</li></ul><p><strong>Do not install the indoor unit in the following locations:&#xA0;</strong></p><ul><li style="font-size: 16px;">Near an obstacle that will block air inlets and outlets.&#xA0;</li><li style="font-size: 16px;">Near public streets, crowded areas, or places where noise from the unit will disturb others.&#xA0;</li><li style="font-size: 16px;">Near animals or plants that will be harmed by hot air discharge.&#xA0;</li><li style="font-size: 16px;">Near any source of combustible gas.&#xA0;</li><li style="font-size: 16px;">A location that is exposed to large amounts of dust.&#xA0;</li><li><span style="font-size: 16px;">A location exposed to an excessive amount of salty air.</span>&#xA0;</li></ul><p><strong>Special considerations for extreme weather:&#xA0;</strong></p><ul><li style="font-size: 16px;"><strong>If the outdoor unit is exposed to strong wind:</strong> Install the unit so that the air outlet fan is at a 90-degree angle to the wind direction. If necessary, build a barrier in front of the unit to protect it from extremely strong winds.&#xA0;</li><li style="font-size: 16px;"><strong>If the outdoor unit is frequently exposed to heavy rain or snow:</strong> Build a shelter above the unit to protect it from rain or snow, ensuring the airflow is not obstructed.&#xA0;</li><li style="font-size: 16px;"><strong>If the outdoor unit is frequently exposed to salty air (seaside):</strong> Use an outdoor unit specifically designed for corrosion resistance.<img src="https://attachments.gorgias.help/Q9r0k7BYaV2vg13y/hc/9JWjXVxG8m6DvMqm/2026041716-abf2710c-d1b5-4dc4-b4d0-fb04b3a690d4-cyb20_extreme_weather.png" style="width: 800px;" class="fr-fic fr-dib fr-bordered">&#xA0;</li></ul>

Select the Installation Locations for UYB-20 Floor-Ceiling Flex Indoor & Outdoor Units

This article explains how to hang the indoor unit for UYB-20 floor-ceiling flex systems.

<h2 id="isPasted"><u>Introduction</u></h2><p>This article explains how to hang the indoor unit for UYB-20 floor-ceiling flex systems.&#xA0;</p><h2 id="note"><u>Note</u></h2><ul><li style="font-size: 16px;">Completely align the unit body with the hole. Ensure the unit and hole are the same size before moving on.&#xA0;</li></ul><h2 id="hanging-methods"><u>Hanging Methods</u></h2><p><strong>Original Concrete Bricks</strong></p><p>Install the hanging hook with the expansion bolt into concrete. Ensure it is installed at a depth of 1-3/4~2 inches (45~50 mm) to prevent loosening.&#xA0;<img src="https://attachments.gorgias.help/Q9r0k7BYaV2vg13y/hc/9JWjXVxG8m6DvMqm/2026050620-e2e1b570-34b2-4bb5-aea1-3b399debc4d9-uyb_hang_idu_original_concrete.png" style="width: 300px;" class="fr-fic fr-dib fr-bordered"></p><p><strong>New Concrete Bricks</strong></p><p>Inlay or embed the screw bolts.&#xA0;<img src="https://attachments.gorgias.help/Q9r0k7BYaV2vg13y/hc/9JWjXVxG8m6DvMqm/2026050620-b9571fac-e00f-4e00-a5ba-f0c3ea8c4e0c-uyb_hang_idu_new_concrete.png" style="width: 500px;" class="fr-fic fr-dib fr-bordered"></p><p><strong>Steel Roof Beam Structures</strong></p><p>Install and use the supporting steel angle.&#xA0;<img src="https://attachments.gorgias.help/Q9r0k7BYaV2vg13y/hc/9JWjXVxG8m6DvMqm/2026050620-02fe04d6-6eb8-42d9-b4e3-b450f8701f92-uyb_hang_idu_steel_roof.png" style="width: 500px;" class="fr-fic fr-dib fr-bordered"></p><p><strong>Wooden Structures</strong></p><p>Place the wood mounting across the roof beam, then install the hanging screw bolts.&#xA0;<img src="https://attachments.gorgias.help/Q9r0k7BYaV2vg13y/hc/9JWjXVxG8m6DvMqm/2026050620-75b44e07-361c-4986-950a-39695b481774-uyb_hang_idu_wooden.png" style="width: 500px;" class="fr-fic fr-dib fr-bordered"></p><h2 id="steps"><u>Steps</u></h2><p>1. Install and fit the pipes and wires after finishing the installation of the main body.&#xA0;</p><p>When choosing a starting, determine which direction the pipes will run.&#xA0;</p><p>2. Install the hanging screw bolts.&#xA0;</p><ul><li style="font-size: 16px;">Cut off the roof beam.&#xA0;</li><li style="font-size: 16px;">Strengthen the area at which the cut was made and consolidate the roof beam.&#xA0;</li></ul><p>3. Before mounting the machine, position the refrigerant pipes, drainpipes, and indoor and outdoor wires to the connection points.&#xA0;</p><p>4. Drill four holes, 4 inches (102 mm) deep, at the ceiling hook positions into the internal ceiling.&#xA0;</p><p>Ensure to hold the drill at a 90-degree angle to the ceiling.&#xA0;</p><p>5. Secure the bolt using the included washers and nuts.&#xA0;</p><p>6. Install the four suspension bolts.&#xA0;</p><p>7. Mount the indoor unit. This process will require two people to lift and secure the indoor unit.&#xA0;</p><p>8. Insert the suspension bolts into the unit&apos;s hanging holes. Fasten them using the included washers and nuts.&#xA0;<img src="https://attachments.gorgias.help/Q9r0k7BYaV2vg13y/hc/9JWjXVxG8m6DvMqm/2026050620-95a7e3fe-f9d1-4112-a5fd-65547e5207aa-cyb20_hang_idu_5.png" class="fr-fic fr-dib fr-bordered"></p><p>9. Remove the side board and grille.&#xA0;<img src="https://attachments.gorgias.help/Q9r0k7BYaV2vg13y/hc/9JWjXVxG8m6DvMqm/2026050620-64d3c1c5-bffe-41e7-a13b-39ede8b25c24-uyb_hang_idu_side_board.png" style="width: 500px;" class="fr-fic fr-dib fr-bordered"></p><p>10. Mount the indoor unit onto the hanging screw bolts with a block. Position the indoor flat using a level indicator to prevent leaks.&#xA0;</p><p>Confirm the minimum drain tilt is 1/100 or more.&#xA0;<img src="https://attachments.gorgias.help/Q9r0k7BYaV2vg13y/hc/9JWjXVxG8m6DvMqm/2026050620-7b8e35b8-3906-4987-8d06-4535ff0e97a9-uyb_hang_idu_screw_bolt.png" style="width: 500px;" class="fr-fic fr-dib fr-bordered"></p><p><br></p><p><br></p>

Hang the Indoor Unit for UYB-20 Floor-Ceiling Flex Systems

This article explains how to install the conduit installation plate for UYB-20 floor-ceiling flex systems.

<h2 id="introduction"><u>Introduction</u></h2><p>This article explains how to install the conduit installation plate for UYB-20 floor-ceiling flex systems.&#xA0;</p><p>The conduit installation plate can be installed on the ceiling or the wall.&#xA0;</p><h2 id="ceiling-installation"><u>Ceiling Installation</u></h2><p id="isPasted">1.&#xA0; &#xA0;&#xA0;Attach the sheath connection (not supplied) to the wire hole of the conduit installation plate.</p><p>2. &#xA0; &#xA0;Attach the conduit installation plate to the unit&apos;s chassis.<img src="https://attachments.gorgias.help/Q9r0k7BYaV2vg13y/hc/9JWjXVxG8m6DvMqm/2026050712-996a7d25-081c-41df-bb25-18ba49fa9065-uyb_drain_slope.png" style="width: 300px;" class="fr-fic fr-dib fr-bordered"></p><h2 id="wall-mounted-installation"><u>Wall-Mounted Installation</u></h2><p id="isPasted">1.&#xA0; &#xA0;&#xA0;Attach the sheath connection (not supplied) to the wire hole of the conduit installation plate.</p><p>2. &#xA0; &#xA0;Attach the conduit installation plate to the unit&apos;s chassis.<img src="https://attachments.gorgias.help/Q9r0k7BYaV2vg13y/hc/9JWjXVxG8m6DvMqm/2026050712-fe6b1d6c-8bf5-4a27-839c-92e2a6f7aa62-uyb_drain_slope_wall.png" style="width: 300px;" class="fr-fic fr-dib fr-bordered"></p><h2 id="knockout-holes"><u>Knockout Holes</u></h2><p>During installation, open the corresponding round knockout holes as shown in the illustration. Rectangular knockout holes are not permitted.&#xA0;<img src="https://attachments.gorgias.help/Q9r0k7BYaV2vg13y/hc/9JWjXVxG8m6DvMqm/2026050712-1e2d669b-550a-4c38-b2ac-242ed242ecc1-uyb_ceiling_installation_conduit_knockout_holes.png" style="width: 500px;" class="fr-fic fr-dib fr-bordered"></p><h2 id="wire-hole"><u>Wire Hole</u></h2><p>1. Rubber rings are used to fill the excess space in the three crossing holes of the electronic control box.&#xA0;<img src="https://attachments.gorgias.help/Q9r0k7BYaV2vg13y/hc/9JWjXVxG8m6DvMqm/2026050712-694c2ab2-aeb9-4c1e-a596-5934a5101f4e-uyb_installation_conduit_rubber_ring.png" style="width: 400px;" class="fr-fic fr-dib fr-bordered"></p><p>2. The installation plate is used to block the bottom outlet holes when routing cables through the side.&#xA0;<img src="https://attachments.gorgias.help/Q9r0k7BYaV2vg13y/hc/9JWjXVxG8m6DvMqm/2026050712-3fde8959-eb95-4dc2-806f-bf28d676ee41-uyb_installation_plate_rubber_ring.png" style="width: 400px;" class="fr-fic fr-dib fr-bordered"></p>

Install the Conduit Installation Plate for UYB-20 Floor-Ceiling Flex Systems

This article explains how to drill the wall hole for the piping of UYB-20 floor-ceiling flex systems.

<h2 id="isPasted"><u>Introduction</u></h2><p>This article explains how to drill the wall hole for the piping of UYB-20 floor-ceiling flex systems.</p><p>The hole being drilled in the wall is intended for the drainage and refrigerant piping. When drilling the wall hole, ensure to avoid wires, plumbing, and other sensitive components.&#xA0;</p><h2 id="steps"><u>Steps</u></h2><p>1. Determine the wall hole&apos;s location based on the intended position of the outdoor unit.&#xA0;</p><p>2. Drill a hole through the wall using a 2-1/2 (63.5 mm) or 3-1/2 inch (90 mm) core drill. Make sure the hole is angled slightly downward so that the exterior opening is 1/2 inch (12 mm) lower than the interior opening. This slope ensures proper water drainage.&#xA0;<img src="https://attachments.gorgias.help/Q9r0k7BYaV2vg13y/hc/9JWjXVxG8m6DvMqm/2026041713-726a7078-884c-4924-b2af-e05ad18dbbe8-cyb20_drill_wall_hole.png" style="width: 300px;" class="fr-fic fr-dib fr-bordered"></p><p>3. Insert the protective wall cuff into the hole. This protects the edges of the hole and helps create a seal during the final installation steps.&#xA0;</p>

Drill the Wall Hole for UYB-20 Floor-Ceiling Flex System Piping

This article explains how to install the drainpipe for UYB-20 floor-ceiling flex systems.

<h2 id="isPasted"><u>Introduction</u></h2><p>This article explains how to install the drainpipe for UYB-20 floor-ceiling flex systems.&#xA0;</p><p>The drainpipe directs water away from the unit. Improper installation can damage the unit or property.&#xA0;</p><h2 id="prerequisites"><u>Prerequisites&#xA0;</u></h2><p><strong>Caution</strong></p><ul><li style="font-size: 16px;">Insulate all piping to prevent condensation, which could lead to water damage.&#xA0;</li><li style="font-size: 16px;">If the drainpipe is bent or installed correctly, water may leak and cause a water-level switch malfunction.&#xA0;</li><li style="font-size: 16px;">In Heating mode, the outdoor unit will discharge water. Ensure the drain hose is placed in an appropriate area to avoid water damage and slippage.&#xA0;</li><li style="font-size: 16px;">Do not pull the drainpipe forcefully. This could disconnect it.</li></ul><p><strong>Installation Notes</strong></p><ul><li style="font-size: 16px;">When using an extended drainpipe, tighten the indoor connection with an additional protection tube to prevent accidental disconnection.&#xA0;</li><li style="font-size: 16px;">The drainpipe should slope downward at a gradient of at least 1/100 to prevent water from flowing back into the air conditioner.&#xA0;</li><li style="font-size: 16px;">To prevent the pipe from sagging, space the hanging wires every 3-feet, 3-3/8-inches to 4-feet, 11-inches (1-1.5 m).&#xA0;</li><li style="font-size: 16px;">The drainpipe outlet should be at least 2 inches (50 mm) above the ground. If it touches the ground, the unit may become blocked and malfunction.&#xA0;</li><li style="font-size: 16px;">The installation requires a polyethylene tube with an exterior diameter of 1 inch (25 mm). This tube can be obtained at a local hardware store or dealer.&#xA0;</li></ul><h2 id="1-plan-the-piping-layout"><u>1. Plan the Piping Layout</u></h2><p>Before beginning the installation, plan the drainage piping layout and connection.&#xA0;</p><h2 id="2-cut-the-piping"><u>2. Cut the Piping</u></h2><p>Cut the piping according to the intended layout and connection.</p><h2 id="3-insulate-the-drainpipe"><u>3. Insulate the Drainpipe</u></h2><p>Insulate each pipe before beginning the connection, excluding the joint sections. These will be insulated at the end of the procedure.</p><p>Ensure the insulation material is fitted tightly with no gaps. Do not over-tighten the insulation material. This may compress the air out of the material, causing poor insulation and early aging.&#xA0;</p><p><strong>Purpose</strong></p><p>Ensure all piping is properly insulated to prevent condensation. Insufficient insulation may allow dew to form due to low condensate temperatures, resulting in potential water damage.&#xA0;</p><p><strong>Select the Insulation Material</strong></p><p>The insulation material must be made of flame-retardant material. Select a material that complies with local regulations.&#xA0;</p><p>The thickness of the insulation material must be more than 3/8 of an inch (10 mm).&#xA0;</p><p>Apply specialized adhesive to the insulation seams, then secure them with tape. Ensure the tape is at least 2 inches (51 mm) wide. Make sure the tape is applied firmly to prevent condensation.&#xA0;</p><h2 id="4-install-the-drainpipe"><u>4. Install the Drainpipe</u></h2><p>Attach the drainpipe to the indoor unit&apos;s drain line connection.&#xA0;</p><p>Unlike wall-mounted systems, ceiling cassette units and other light commercial air conditioning systems require a PVC drain line. The flexible drain hoses are not suitable for these applications.&#xA0;</p><p>Use a rubber coupler to connect the drainpipe to the PVC drain, ensuring a secure, water-tight seal. The rubber coupler and PVC drain line are sold separately from the system.&#xA0;<img src="https://attachments.gorgias.help/Q9r0k7BYaV2vg13y/hc/9JWjXVxG8m6DvMqm/2026042213-4e973842-7d26-4e9d-a826-d4a71f57ad0d-cyt24_drain_hose_rubber_coupler.png" style="width: 150px;" class="fr-fic fr-dib fr-bordered"></p><p>This is how the drainpipe assembly should look when attached to the PVC line with the rubber coupler.&#xA0;<img src="https://attachments.gorgias.help/Q9r0k7BYaV2vg13y/hc/9JWjXVxG8m6DvMqm/2026042213-a7d2ad10-a90c-44de-aa61-7ab81532c7d4-cyt24_drainpipe_assembly.png" style="width: 300px;" class="fr-fic fr-dib fr-bordered"></p><p>Install the drainpipe assembly as illustrated:&#xA0;<img src="https://attachments.gorgias.help/Q9r0k7BYaV2vg13y/hc/9JWjXVxG8m6DvMqm/2026050713-3df56402-5fcb-4066-842e-a960de08f5bd-uyb_drainpipe_assembly.png" style="width: 600px;" class="fr-fic fr-dib fr-bordered"></p><p>When connecting multiple drainpipes, install them as illustrated:&#xA0;<img src="https://attachments.gorgias.help/Q9r0k7BYaV2vg13y/hc/9JWjXVxG8m6DvMqm/2026050713-d9b468f5-d3a0-49c5-a95c-7515c4343fe0-uyb_drainpipe_assembly_multiple.png" style="width: 600px;" class="fr-fic fr-dib fr-bordered"></p><h2 id="5-pass-the-drainpipe-through-the-wall-hole"><u>5. Pass the Drainpipe Through the Wall Hole</u></h2><p>When passing the drainpipe through the wall hole, make sure the water drains to a safe location where it will not cause water damage or a slipping hazard.&#xA0;</p><p>The drainpipe outlet should be be at least 1-7/8 inches (48 mm) above the ground. If it touches the ground, the unit may become blocked, potentially leading to a malfunction.&#xA0;</p><p>If the water is discharged directly into the sewer, ensure the drain hose has a U or S pipe to prevent odors from coming back into the house.&#xA0;</p><h2 id="isPasted"><u>6. Complete a Drainage Test</u></h2><p>Complete a drainage test for the floor-ceiling flex system.&#xA0;</p><h2 id="7-insulate-the-joint-sections"><u>7. Insulate the Joint Sections</u></h2><p>The pipe joint insulation should 2-4 inches (51-102 mm) longer than the gap to ensure a proper seal.&#xA0;</p><p>Insert the pipe joint insulation into the gap of the existing insulation.&#xA0;</p><p>Ensure the pipe joint insulation is securely fastened to the suction and liquid pipes to prevent gaps. Use glue to paste together the linking part. Do not over-tighten the insulation material. This may compress the air out of the material, causing poor insulation and early aging.&#xA0;</p>

Install the Drainpipe for UYB-20 Floor-Ceiling Flex Systems

This article explains how to install the drain joint for UYB-20 floor-ceiling flex outdoor units.

<h2 id="isPasted"><u>Introduction</u></h2><p>This article explains how to install the drain joint for UYB-20 floor-ceiling flex outdoor units.&#xA0;</p><p>Before anchoring the outdoor unit, install the drain joint at the bottom of the unit. When mounting the outdoor unit on slabs, the installation of the drain joint and tubing is not necessary.&#xA0;</p><p>There are two types of drain joints for the outdoor unit: one with a rubber seal and one without.&#xA0;</p><h2 id="steps"><u>Steps</u></h2><p><strong>If the drain joint comes with a rubber seal, follow these steps:&#xA0;</strong></p><p>1. Fit the rubber seal onto the end of the drain joint connecting to the outdoor unit.&#xA0;</p><p>2. Insert the drain joint into the hole of the unit&apos;s base pan.&#xA0;<img src="https://attachments.gorgias.help/Q9r0k7BYaV2vg13y/hc/9JWjXVxG8m6DvMqm/2026050419-5102da7c-45b8-4f48-88e4-25cd3f1a4c60-ryb_odu_drain_joint_base_pan_hole.png" style="width: 300px;" class="fr-fic fr-bordered fr-dib"></p><p>3. Rotate the drain joint 90-degrees until it clicks into place facing the front of the unit.&#xA0;</p><p>4. Connect a drain hose extension (not included) to the drain joint in order to redirect water from the unit during Heating mode.&#xA0;<img src="https://attachments.gorgias.help/Q9r0k7BYaV2vg13y/hc/9JWjXVxG8m6DvMqm/2026042018-420def83-4c85-4456-bf34-f90ad7a38dea-cyb20_drain_joint_a.png" style="width: 500px;" class="fr-fic fr-dib fr-bordered"></p><p><strong>If the drain joint does not come with a rubber seal, follow these steps:&#xA0;</strong></p><p>1. Insert the drain joint into the base pan hole, then press firmly to ensure it is properly installed and does not become loose.&#xA0;</p><p>2. Connect a drain hose extension (not included) to the drain joint in order to redirect water from the unit during Heating mode.&#xA0;<img src="https://attachments.gorgias.help/Q9r0k7BYaV2vg13y/hc/9JWjXVxG8m6DvMqm/2026042018-e061b965-d459-484c-965c-5140811a2291-cyb20_drain_joint_b.png" style="width: 400px;" class="fr-fic fr-dib fr-bordered"></p><h2 id="notes"><u>Notes</u></h2><ul><li style="font-size: 16px;">In cold climates, make sure the drain hose is as vertical as possible to ensure swift water drainage. If water drains too slowly, it can freeze in the hose and flood into the unit.</li></ul>

Install the Drain Joint for UYB-20 Floor-Ceiling Flex Outdoor Units

This article explains how to mount outdoor units for UYB-20 floor-ceiling flex systems.

<h2 id="isPasted"><u>Introduction</u></h2><p>This article explains how to mount outdoor units for UYB-20 floor-ceiling flex systems.&#xA0;</p><h2 id="mount-the-outdoor-unit"><u>Mount the Outdoor Unit</u></h2><p>Before connecting any pipes or cables, mount the outdoor unit to the ground or a wall-mounted bracket with bolts.&#xA0;</p><p>Decide the best position on the wall or ground and leave enough space in order to carry out maintenance easily.&#xA0;</p><p>If wall mounting, fasten the supporting brackets to the wall using hardware that is particularly suited for the type of wall. Use the appropriate amount of hardware for the application as well. Installing four rubber pads is optional.</p><p>When mounting the outdoor unit on slabs, the installation of the drain joint and tubing is not necessary.&#xA0;<img src="https://attachments.gorgias.help/Q9r0k7BYaV2vg13y/hc/9JWjXVxG8m6DvMqm/2026042213-242b41f9-4fe4-46a1-8da9-8a771b6d9e13-49178f71-ea1d-4c05-918d-5aca43faaca2.png" style="width: 300px;" class="fr-fic fr-dib fr-bordered"></p><p>Follow all national regulations when installing the unit.&#xA0;</p><h2 id="outdoor-unit-dimensions"><u>Outdoor Unit Dimensions<img src="https://attachments.gorgias.help/Q9r0k7BYaV2vg13y/hc/9JWjXVxG8m6DvMqm/2026042019-48fbd2e3-7064-4044-9c51-4a7538602b78-cyb20_odu_dimensions.png" style="width: 800px;" class="fr-fic fr-dib fr-bordered"></u></h2><p>Prepare the installation base of the unit according the dimensions below:&#xA0;</p><table style="width: 100%;"><tbody><tr><td style="background-color: rgb(239, 239, 239); text-align: center; width: 21.4495%;" rowspan="2" class="fr-thick"><strong>Model Number</strong></td><td style="width: 32.7233%; background-color: rgb(239, 239, 239); text-align: center;" rowspan="2" class="fr-thick"><strong>Dimensions<br>W x D x H</strong></td><td style="width: 45.7701%; background-color: rgb(239, 239, 239); text-align: center;" colspan="2" class="fr-thick"><strong>Mounting Dimensions</strong></td></tr><tr><td style="width: 23.1035%; background-color: rgb(239, 239, 239); text-align: center;" class="fr-thick"><strong>Distance A</strong></td><td style="width: 22.5773%; background-color: rgb(239, 239, 239); text-align: center;" class="fr-thick"><strong>Distance B</strong></td></tr><tr><td style="text-align: center; width: 21.4495%;" rowspan="2" class="fr-thick">YN036GMSI20RUG<strong><br></strong></td><td style="width: 32.7233%; text-align: center;" class="fr-thick">37-1/4 x 16-1/4 x 31-7/8 inches</td><td style="width: 23.1035%; text-align: center;" class="fr-thick">26-1/2 inches</td><td style="width: 22.5773%; text-align: center;" class="fr-thick">15-7/8 inches</td></tr><tr><td style="width: 32.7233%; text-align: center;" class="fr-thick">946 x 413 x 810 mm</td><td style="width: 23.1035%; text-align: center;" class="fr-thick">673 mm</td><td style="width: 22.5773%; text-align: center;" class="fr-thick">403 mm</td></tr><tr><td style="text-align: center; width: 21.4495%;" rowspan="2" class="fr-thick">YN048GMSI20RUG</td><td style="width: 32.7233%; text-align: center;" class="fr-thick">37-1/2 x 16-3/8 x 52-1/2 inches</td><td style="width: 23.1035%; text-align: center;" class="fr-thick">25 inches</td><td style="width: 22.5773%; text-align: center;" class="fr-thick">16 inches</td></tr><tr><td style="width: 32.7233%; text-align: center;" class="fr-thick">952.5 x 416 x 1,333.5 mm</td><td style="width: 23.1035%; text-align: center;" class="fr-thick">634 mm</td><td style="width: 22.5773%; text-align: center;" class="fr-thick">404 mm</td></tr></tbody></table><h2 id><br></h2><h2 id="install-the-unit-on-the-ground-or-a-concrete-mounting-platform"><u>Install the Unit on the Ground or a Concrete Mounting Platform</u></h2><p>If installing the outdoor unit on the ground or a concrete mounting platform, follow these steps:&#xA0;</p><ol><li style="font-size: 16px;">Mark the positions for the four bolts based on the dimensions.&#xA0;</li><li style="font-size: 16px;">Pre-drill holes for the bolts.&#xA0;</li><li style="font-size: 16px;">Clean concrete dust away from the holes.&#xA0;</li><li style="font-size: 16px;">Place a nut on the end of each bolt.&#xA0;</li><li style="font-size: 16px;">Hammer the bolts into each hole.&#xA0;</li><li style="font-size: 16px;">Remove the nuts from the bolts and place the outdoor unit onto them.&#xA0;</li><li style="font-size: 16px;">Put washers onto each bolt, then replace each of the nuts.&#xA0;</li><li style="font-size: 16px;">Use a wrench to tighten each nut until snug.</li></ol><h2 id="install-multiple-outdoor-units"><u>Install Multiple Outdoor Units</u></h2><p>If multiple outdoor units are being installed in a row, follow these guidelines:</p><p><img src="https://attachments.gorgias.help/Q9r0k7BYaV2vg13y/hc/9JWjXVxG8m6DvMqm/2026042215-14e11bb1-f320-4e36-912b-306d3134d958-cyb20_odu_multiple.png" style="width: 500px;" class="fr-fic fr-dib fr-bordered"></p><p>H: Unit height.&#xA0;</p><p>L: Height of the wall behind the unit.&#xA0;</p><p>A: Distance between the unit and wall.&#xA0;</p><table style="width: 100%;"><tbody><tr><td style="width: 33.3333%; text-align: center;" class="fr-thick"><br></td><td style="width: 33.3333%; text-align: center;" class="fr-thick"><strong>L</strong><br></td><td style="width: 33.3333%; text-align: center;" class="fr-thick"><strong>A</strong><br></td></tr><tr><td style="width: 33.2357%; text-align: center;" rowspan="2" class="fr-thick"><strong>L &#x2264; H</strong><br></td><td style="width: 33.3333%; text-align: center;" class="fr-thick">L &#x2264; 1/2H</td><td style="width: 33.3333%; text-align: center;" class="fr-thick">9-3/4 in (250 mm) or more</td></tr><tr><td style="width: 33.3333%; text-align: center;" class="fr-thick">1/2H &lt; L &#x2264; H</td><td style="width: 33.3333%; text-align: center;" class="fr-thick">11-3/4 in (300 mm) or more<br></td></tr><tr><td style="width: 33.3333%; text-align: center;" class="fr-thick"><strong>L &gt; H</strong><br></td><td style="width: 66.4714%; text-align: center;" colspan="2" class="fr-thick">Cannot be installed</td></tr></tbody></table>

Mount the Outdoor Unit for UYB-20 Floor-Ceiling Flex Systems

This article explains how to connect the electrical wiring for UYB-20 floor-ceiling flex systems.

<h2 id="isPasted"><u>Introduction</u></h2><p>This article explains how to connect the electrical wiring for UYB-20 floor-ceiling flex systems.&#xA0;</p><h2 id="warnings"><u>Warnings</u></h2><p>Before performing any electrical work, read these warnings:&#xA0;</p><p><strong>General Warnings</strong></p><ul><li style="font-size: 16px;">All wiring must comply with local and national electrical codes and regulations. A licensed electrician must install all the wiring.&#xA0;</li><li style="font-size: 16px;">All electrical connections must be made according to the electrical connection diagram located on the panels of the indoor and outdoor units.&#xA0;</li><li style="font-size: 16px;">If there is a serious safety issue with the power supply, stop work immediately. Explain the reasoning to the client and refuse to continue the installation until the safety issue is properly resolved.</li></ul><p><strong>Power Warnings</strong></p><ul><li style="font-size: 16px;">The power voltage must be within 90-110% of the rated voltage. Insufficient power supply can cause a malfunction, electrical shock, or fire. &#xA0;</li><li style="font-size: 16px;">Only connect the units to an individual branch circuit. Do not connect other equipment to the same power circuit. &#xA0;</li></ul><p><strong>Wiring Warnings</strong></p><ul><li style="font-size: 16px;">Firmly connect every wire. Loose wiring can cause the terminal to overheat, resulting in product malfunction and possible fire.&#xA0;</li><li style="font-size: 16px;">Keep the wiring away from the copper tube, as the refrigerant circuit can become extremely hot.&#xA0;</li><li style="font-size: 16px;">Do not let wires touch or rest against the refrigerant tubing, compressor, or any moving parts.&#xA0;</li><li style="font-size: 16px;">Do not cross the electrical wiring with the signal wiring. This may cause distortion, interference, or possibly damage to the circuit boards.&#xA0;</li><li style="font-size: 16px;">Do not house wires of different voltages within the same wire tube. Avoid using metal wire tubes in environments prone to acid or alkali corrosion; use plastic wire tubes instead.&#xA0;</li><li style="font-size: 16px;">Do not place wire connect joints inside the tubing. If a wire connect joint is necessary, use a connection box at the point of the joint.&#xA0;</li></ul><h2 id="prerequisites"><u>Prerequisites</u></h2><p>Complete these prerequisites before connecting the electrical wiring:&#xA0;</p><ul><li style="font-size: 16px;">Turn off the main power to the system. After powering off the system, wait 10 minutes or more before touching the electrical components in order to avoid electrical shock.&#xA0;</li><li style="font-size: 16px;">Properly ground the system. &#xA0;</li><li style="font-size: 16px;">If the unit has an auxiliary electric heater, install it at least 3-feet, 3-3/8-inches (1 m) away from any combustible materials.&#xA0;</li><li style="font-size: 16px;">Install an external surge suppressor at the outdoor disconnect (recommended).&#xA0;</li><li style="font-size: 16px;">If connecting power to fixed wiring, incorporate a current leakage protection switch or circuit breaker that disconnects all poles with a contact separation of at least 1/8 of an inch (3 mm). Use only an approved switch or circuit breaker.</li><li style="font-size: 16px;"><strong>Service Disconnect:&#xA0;</strong>When the air conditioner&apos;s maximum current is more than 16A, use a service disconnect or leakage protection switch with a protective device (purchase separately). When the air conditioner&apos;s maximum current is less than 16A, equip the power cord of the air conditioner with a plug (purchase separately).&#xA0;<br><br>Select the service disconnect as required by local, regional, and national codes. In North America, wire the appliance according to NEC and CEC requirements.&#xA0;<br><br>The cograph is for explanation purposes only. The machine may be slightly different. The actual shape shall prevail.&#xA0;</li></ul><p><img src="https://attachments.gorgias.help/Q9r0k7BYaV2vg13y/hc/9JWjXVxG8m6DvMqm/2026041718-c55f0d85-7555-4139-affb-b2459ce5e802-cyb20_service_disconnect.png" style="width: 800px;" class="fr-fic fr-dib fr-bordered"></p><h2 id="cable-wiring-specifications"><u>Cable Wiring Specifications</u></h2><table style="width: 100%;"><tbody><tr><td style="width: 33.2357%; background-color: rgb(239, 239, 239); text-align: center;" rowspan="2" class="fr-thick"><strong>UYB-20</strong></td><td style="width: 33.3333%; background-color: rgb(239, 239, 239); text-align: center;" class="fr-thick"><strong>36K</strong></td><td style="width: 33.3333%; background-color: rgb(239, 239, 239); text-align: center;" class="fr-thick"><strong>48K</strong></td></tr><tr><td style="width: 66.4714%; background-color: rgb(239, 239, 239); text-align: center;" colspan="2" class="fr-thick"><strong>Sectional Area</strong></td></tr><tr><td style="width: 33.3333%; text-align: center;" class="fr-thick">Power Supply Cable</td><td style="width: 33.3333%; text-align: center;" class="fr-thick">14 AWG</td><td style="width: 33.3333%; text-align: center;" class="fr-thick">12 AWG</td></tr><tr><td style="width: 33.3333%; text-align: center;" class="fr-thick">Connection Cable for Communication Between the&#xA0;<br>Indoor and Outdoor Units</td><td style="width: 33.3333%; text-align: center;" class="fr-thick">16 AWG</td><td style="width: 33.3333%; text-align: center;" class="fr-thick">16 AWG</td></tr></tbody></table><p><br></p><p>Consult the nameplate on the system for detailed electrical specifications. The power wire sizes in the table assume the largest allowable fuse.&#xA0;</p><p>The 230V systems requires a double-pole breaker. The tandem-type will not work.<img src="https://attachments.gorgias.help/Q9r0k7BYaV2vg13y/hc/9JWjXVxG8m6DvMqm/2026042416-51127370-f615-4594-91c5-6401b87817d8-cyb20_wiring_doublepole.png" style="width: 300px;" class="fr-fic fr-dib fr-bordered"></p><h2 id="connection-diagram"><u>Connection Diagram</u></h2><p><img src="https://attachments.gorgias.help/Q9r0k7BYaV2vg13y/hc/9JWjXVxG8m6DvMqm/2026041718-53b39430-b419-4783-9171-eb31281d065d-cyb20_connection_diagram.png" style="width: 800px;" class="fr-fic fr-dib fr-bordered"></p><h2 id="connect-the-wiring"><u>Connect the Wiring</u></h2><p>Connect the outdoor unit wires before connecting the indoor unit wires.&#xA0;</p><p><strong>Outdoor Unit Wiring</strong></p><p>1. Prepare the cable for connection.</p><p style="margin-left: 20px;">a) Begin by selecting the correct cable size and type according to local electrical codes and regulations.&#xA0;</p><p style="margin-left: 20px;">b) The minimum circuit ampacity of the unit determines the size of the power supply cable, signal cable, fuse, and switch needed. The minimum circuit ampacity is indicated on the nameplate located on the unit&apos;s side panel. Refer to the nameplate to select the correct cable, fuse, or switch.&#xA0;</p><p style="margin-left: 20px;">c) Use wire strippers to strip the rubber jacket from both ends of the signal cable to reveal 5-7/8 inches (150 mm) of the wire.&#xA0;</p><p style="margin-left: 20px;">d) Strip the insulation from the ends of the cable.&#xA0;</p><p style="margin-left: 20px;">e) Use a wire crimper to crimp U-lugs on the ends.&#xA0;</p><p>2. Remove the two screws attached on the front and side panels, then detach the panel to access the wire connections. (Outdoor Unit A).&#xA0;</p><p>Unscrew the electrical wiring cover and remove it (Outdoor Unit B).&#xA0;<img src="https://attachments.gorgias.help/Q9r0k7BYaV2vg13y/hc/9JWjXVxG8m6DvMqm/2026041719-6f68d645-9a14-4fb9-b637-386d2da603d2-cyb20_odu_wiring_screws.png" style="width: 400px;" class="fr-fic fr-dib fr-bordered"></p><p>3. Connect the U-lugs to the terminals, matching the wire colors or labels with those on the terminal block. Firmly screw each U-lug to its corresponding terminal. Strictly follow the wiring diagram inside the electrical box cover when connecting the wires.&#xA0;</p><p>Select different colors for different wires according to relevant regulations. Ensure the wire colors for the wire colors for the outdoor unit and terminals match those used for the indoor unit.&#xA0;</p><p>Do not connect the power wire to the signal wire terminal. If the power and signal wires run parallel, place the wires in their own wire tube and maintain a gap of at least 11-3/4 inches (300 mm).&#xA0;</p><p>4. Clamp down the cable with the cable clamp. The cable must not be loose or pull on the U-lugs.&#xA0;</p><p>5. Insulate unused wires with electrical tape. Keep them away from any electrical or metal parts.&#xA0;</p><p>6. Reinstall the electrical control box&apos;s cover.&#xA0;</p><p><strong>Indoor Unit Wiring</strong></p><p>1. Prepare the cable for connection.&#xA0;</p><p style="margin-left: 20px;">a) Use wire strippers to strip the rubber jacket from both ends of the signal cable to reveal 5-7/8 inches (150 mm) of the wire.&#xA0;</p><p style="margin-left: 20px;">b) Strip the insulation from the ends of the cable.&#xA0;</p><p style="margin-left: 20px;">c) Use a wire crimper to crimp U-lugs on the ends.</p><p>2. Open the indoor unit&apos;s front panel. Use a screwdriver to remove the electrical control box cover.&#xA0;</p><p>3. Thread the power and signal cables through the wire outlet.&#xA0;</p><p>4. Connect the U-lugs to the terminals, matching the wire colors or labels with those on the terminal block. Firmly screw each U-lug to its corresponding terminal. Refer to the serial number and wiring diagram inside the electrical box cover when connecting the wires.&#xA0;<img src="https://attachments.gorgias.help/Q9r0k7BYaV2vg13y/hc/9JWjXVxG8m6DvMqm/2026050713-f73b0602-11ff-4e16-b62a-d6cd43101552-uyb_connective_wiring_diagram.png" style="width: 500px;" class="fr-fic fr-dib fr-bordered"></p><p>5. Clamp down the cable with the cable clamp. The cable must not be loose or pull on the U-lugs.&#xA0;</p><p>6. Reattach the electrical control box&apos;s cover.&#xA0;</p><p><strong>Magnetic Ring (if supplied with the accessories):</strong> Pass the belt through the magnetic ring&apos;s hole to attach it to the cable.&#xA0;<img src="https://attachments.gorgias.help/Q9r0k7BYaV2vg13y/hc/9JWjXVxG8m6DvMqm/2026042417-2fe9762e-9869-4426-bb74-1b7b9458be22-cyb20_wiring_magnetic_ring.png" style="width: 500px;" class="fr-fic fr-dib fr-bordered"></p>

Connect the Electrical Wiring for UYB-20 Floor-Ceiling Flex Systems

Chat with one of our friendly reps to get help quick.

Something on your mind not found here? E-mail us.

We offer phone support if you don't want to type.

Support Center

UYB Flex Units

Installation

Ductless & Ducted Systems

Indoor Units

Flex Units

Pioneer Offers Hyper-Heat Units

Pioneer Systems Offer Both Heating & Cooling Functions

Understand the Difference Between 115V & 230V Systems

Understand the Refrigerants Used for Each Model

How to Choose a System

Mini Splits are Capable of Using Fewer Indoor Units than the Outdoor Unit’s Zonal Capacity

Pioneer Mini Splits Function as Dehumidifiers

Pioneer Offers Different Lineset Lengths

Pioneer Offers Pre-Charged Linesets

Pioneer Offers Pre-Flared Linesets

Pioneer Systems Include Factory Pre-Charged Refrigerant

Single-Zone Mini Splits Cannot be Used with Multiple Indoor Units

Understand the Allowable Zone Combinations for Multi-Zone Systems

Understand how Mini Splits are Powered

Understand the Life Expectancy of Pioneer Systems

Understand the Meaning of “Multi-Zone”

Mini-Split Basics

Determine the Unit Size Needed for Your Space

Match the Lineset Diameter to Your Pioneer Indoor Unit

Understand Why Short Cycling Occurs When Sizing Systems

Sizing & Efficiency Guide

Start Here

Understand the Differences Between Inverter+ & Inverter++ Systems

Understand the Differences Between the Wall-Mounted Ductless Mini Splits

Understand Which Units are Rated Energy-Star

Compare Models

Learn About the Discounts Available

Learn About the Energy-Star Tax Credits Available for Pioneer Systems

Learn More about IRA Tax Credits

Learn Why Your Pioneer Discount Code Only Says "SAMPLE"

Redeem Your Pioneer Rewards Points When Shopping Online

Understand How to Manage Multiple Credit Card Charges with Pioneer

Financing & Payment

Learn About Our Shipping & Delivery Details

Understand the Qualifications for Free Shipping

Order Status & Shipping

Diamante Essenza High-Wall (WYT-17) Overview

Diamante Pro High-Wall (WYT-20) Overview

Quantum Fresh High-Wall (WYT-FA) Overview

Quantum Hyperformance High-Wall (WYT-25) Overview

Quantum Ultra Ceiling Cassette (CYT-24) Overview

Quantum Ultra Ducted Ceiling Concealed (RYT-24) Overview

Quantum Ultra Floor-Ceiling Flex (UYT-24) Overview

Quantum Ultra High-Wall (WYT-24) Overview

Quantum Ultra Multi-Zone Overview

Vertex Ducted Central Split (DYC-18) Overview

Ducted & Ductless Systems

ECOasis 50 Ductless Wall-Mounted Single-Room Energy Recovery Ventilator (ERV) Overview

ECOasis 150 Ductless Wall-Mounted Single-Room Energy Recovery Ventilator (ERV) Overview

Energy Recovery Ventilators

QHD070 Whole-House Ducted Dehumidifier (QHD) Overview

High Performance Dehumidifier

Full Inverter Rooftop RV Air Conditioner Heat Pump (PYZ) Overview

Under-Bench RV Inverter Packaged Heat Pump Air Conditioner (PYR) Overview

Recreational Vehicle Systems

Product Line Overviews

Find Out How to Complete Returns

Figure Out How to Start Your Return

Learn About Our Policy for Undeliverable or Refused Shipments

Learn About Our Return Policy

Understand How to Return an Item

Understand the Eligibility Requirements for Refunds

Understand Our Return Fees

Understand Our Return Process

Returns & Refunds

Shopping & Pre-Purchase

Find Out if Our Systems Support Self-Installation

Locate an Installer for Your System

Understand the Cost & Time Spent on Installing Systems

First-Time Installations

Conduct Drainage Tests for Ceiling Cassette Systems

Conduct Drainage Tests for Ducted Ceiling Concealed Systems

Conduct Drainage Tests for Wall-Mounted Systems

Conduct Test Runs

Connect the Refrigerant Piping

Installation Basics

Can Wall-Mounted Indoor Units Be Installed Onto the Ceiling Instead?

Does the Indoor Unit Need Additional Hardware for Wall Mounting?

Lineset Installation FAQ

What are the Drilling Requirements to Install Drain & Refrigerant Lines?

What are the Requirements for Installing Wall-Mounted Systems?

What is the Difference Between the 6-foot Plastic Whip & 4-Lead Wire?

What is the Ideal Height for Mounting Indoor Units?

What is the Standard Wire Gauge Needed for Connections?

General Installation FAQ

Ceiling Cassettes

Ducted Ceiling Concealed

Ducted Central Split

Wall-Mounted Units

Install Outdoor Units: Getting Started

Connect the Electrical Wiring for Outdoor Units

Mount the Outdoor Unit

Select the Installation Location for Outdoor Units

Select the Installation Location for Ducted Central Split Outdoor Units

Set Up the Condensate Water Drainage for Outdoor Units

Understand How to Install Ducted Central Split Outdoor Units on Support Pads

Outdoor Units

Install ECOasis 50 Energy Recovery Ventilators

Install ECOasis 150 Energy Recover Ventilators

Energy Recovery Ventilator

Connect the Drain Fitting for QHD070 Whole-House Ducted Dehumidifiers

High Performance Dehumidifiers

Install Rooftop RV Systems: Getting Started

Create the Roof Opening for Rooftop RV Systems

Install the Air Duct & Top Mounting Plate for Rooftop RV Systems

Mount the Panel for Rooftop RV Systems

Place the Unit onto the Roof for Rooftop RV Systems

Setup the Electrical Wiring for Rooftop RV Systems

Setup the System Connections for Rooftop RV Systems

Understand the Installation Requirements for Rooftop RV Systems

Rooftop RV Inverter

Install Under-Bench RV Systems: Getting Started

Connect & Power Up Under-Bench RV Systems

Create the Floor Openings for Under-Bench RV Systems

Create the Recirculation Air Opening for Under-Bench RV Systems

Fasten the Under-Bench RV System into Place

Install the Wall Thermostat for Under-Bench RV Systems

Understand the Ductwork Best Practices for Under-Bench RV Systems

Understand the Installation Requirements for Under-Bench RV Systems

Under-Bench RV Inverter

Understand the DIP Switches for Vertex Ducted Central Split Systems

DIP Switch Layouts

Turn the LED Display On or Off

Understand the Display Board for Ducted Ceiling Concealed Systems

Understand the Display Panel for Rooftop RV Systems

Understand the Front Panel Displays for Ceiling Cassette Systems

Understand the Front Panel Display for Floor-Ceiling Flex Systems

Understand the Front Panel Display for Wall-Mounted Systems

Understand the Master Unit Display for ECOasis 50 Energy Recovery Ventilators

Understand the Onboard Controller & Terminal Block Layout for QHD070 Whole-House Ducted Dehumidifiers