This article provides the steps for flushing A2L refrigerants from your system.

<h2 id="introduction">Introduction</h2>This article provides the steps for flushing A2L refrigerants from your system.&#xA0;To ensure safety, flush the system with oxygen-free nitrogen (OFN). Do not use compressed air or oxygen for flushing. Repeat this process multiple times if needed.&#xA0;<h2 id="steps">Steps</h2><ol><li>Break the system vacuum with OFN.&#xA0;</li><li>Fill the system until the working pressure is reached.&#xA0;</li><li>Vent the system to atmospheric pressure.&#xA0;</li><li>Pull the system down to vacuum.&#xA0;</li><li>Repeat this process until no refrigerant remains in the system.&#xA0;</li><li>When the final OFN charge is introduced, vent the system to atmospheric pressure to allow for safe work. Position the vacuum pump outlet away from ignition sources and ensure adequate ventilation. Note: This step is critical before performing any brazing on pipework.&#xA0;</li></ol>

Flush A2L Refrigerants from Your System

This article provides the steps for removing and evacuating A2L refrigerants from your system.

<h2 id="introduction">Introduction</h2>This article provides the steps for removing and evacuating A2L refrigerants from your system.&#xA0;When accessing the refrigerant circuit for repairs or other procedures, follow the industry-standard practices. In addition, take precautions for flammability.&#xA0;<h2 id="steps">Steps</h2><ol><li>Recover the refrigerant into approved recovery cylinders.&#xA0;</li><li>Purge the circuit using an inert gas, such as oxygen-free nitrogen (OFN).&#xA0;</li><li>Evacuate the system.&#xA0;</li><li>Purge the circuit again using inert gas.&#xA0;</li><li>Open the circuit by cutting or brazing.&#xA0;</li></ol>

Removal & Evacuation for A2L Refrigerants

This article provides service information for A2L refrigerants.

This article provides service information for A2L refrigerants.&#xA0;<h4 id="general-service-information">General Service Information</h4><ul><li>Store the appliance in a manner that prevents mechanical damage.&#xA0;</li><li>Competent personnel must carry out any work procedures affecting safety measures.&#xA0;</li><li>Do not attempt to accelerate the defrosting process or remove the frost manually.&#xA0;</li><li>Follow the manufacturer&apos;s recommended procedures.&#xA0;</li><li>Store the appliance in a room free of continuously operating ignition sources, such as open flames, active gas appliances, and operating electric heaters.&#xA0;</li><li>Do not pierce or incinerate the appliance or its components.&#xA0;</li><li>Be aware that refrigerants may be odorless.&#xA0;</li></ul>Initial Safety Checks<ul><li>Fully discharge the capacitors in a controlled manner to prevent sparking.&#xA0;</li><li>Verify that no live electrical components or exposed wiring are present during system charging, refrigerant recovery, or purging.&#xA0;</li><li>Confirm that the earth bonding continuity is maintained.&#xA0;</li></ul><h4 id="work-area-inspection">Work Area Inspection</h4><ul><li>Before performing service on systems containing flammable refrigerants, complete safety checks to minimize the risk of ignition.</li><li>When repairing the refrigeration system, observe all the following precautions before beginning any work.&#xA0;</li><li id="isPasted">Inform all maintenance personnel and individuals in the vicinity about the nature of the work being performed.&#xA0;</li><li>Avoid working in confined spaces whenever possible.&#xA0;</li><li>Section off the work area to prevent unauthorized access.&#xA0;</li></ul><h4 id="work-procedure">Work Procedure</h4><ul><li>Conduct all work under a controlled process to minimize the risk of flammable gas or vapor from being present during service.&#xA0;</li></ul>Area Ventilation<ul><li>Ensure that the work is conducted in either an open area or in a space with adequate ventilation before breaking into the system or performing any heat-producing tasks.&#xA0;</li><li id="isPasted">Maintain ventilation throughout the duration of the work.&#xA0;</li><li>Ensure that the area is free from flammable materials and conditions are controlled to maintain a safe working environment.&#xA0;</li><li>Ensure that the ventilation system effectively disperses any released refrigerant and directs it safely to an external atmosphere, if possible.&#xA0;</li></ul>Checking for Refrigerant Presence<ul><li>Monitor the work area for refrigerant leaks using an appropriate refrigerant detector before and during service.&#xA0;</li><li>Ensure that the leak detection equipment used is suitable for flammable refrigerants, such as non-sparking, adequately sealed, or intrinsically safe.</li></ul>Presence of Fire Extinguisher<ul><li>If performing any hot work on the refrigeration equipment or its associated components, ensure that appropriate fire extinguishing equipment is readily available. Position a dry powder or CO&#xB2; fire extinguisher adjacent to the charging area.</li></ul>Elimination of Ignition Sources<ul><li>Do not use ignition sources that could pose a fire or explosion risk when conducting any work involving the exposure of the refrigeration system piping.&#xA0;</li><li>Keep all potential ignition sources, including smoking, at a safe distance from the installation, repair, removal, disposal areas, and locations where refrigerant may be released unintentionally into the surrounding space.&#xA0;</li><li>Before commencing work, inspect the area to ensure that no flammable hazards or ignition risks are present.&#xA0;</li><li>Clearly display &quot;No Smoking&quot; signs in the work area.&#xA0;</li></ul>Inspection of Refrigeration Equipment<ul><li>When replacing electrical components, ensure that they meet the correct specifications and are suitable for its intended purpose.&#xA0;</li><li>Follow the manufacturer&apos;s maintenance and service guidelines.&#xA0;</li><li>If unsure, consult the manufacturer&apos;s technical support department for guidance.&#xA0;</li></ul>Inspection for Installation Using Flammable Refrigerants<ul><li>Ensure that the refrigerant charge size complies with the minimum room size requirements when installing refrigerant-containing components.&#xA0;</li><li>Verify that the ventilation equipment and exhaust outlets are functioning properly and free from obstructions.&#xA0;</li><li>If using an indirect refrigerant circuit, inspect the secondary circuit for any presence of refrigerant.&#xA0;</li><li>Confirm that all equipment markings remain visible and legible. Replace or correct any illegible markings or signs.&#xA0;</li><li>Install the refrigeration piping and components in locations where they are not exposed to substances that could cause corrosion. If exposure is unavoidable, verify that the components are either made from corrosion-resistant materials or are adequately protected against corrosion.&#xA0;</li></ul>Inspection of Electrical Devices<ul><li>Ensure that the repair and maintenance of electrical components include initial safety checks and a thorough inspection of components.&#xA0;</li><li>If the fault cannot be corrected immediately but continuing work is necessary, implement a temporary solution that is safe and effective.&#xA0;</li><li>Report any temporary measures to the equipment owner, ensuring all relevant parties are informed.&#xA0;</li></ul>Repairs to Sealed Components<ul><li>Replace sealed electrical components, rather than repair them.&#xA0;</li></ul>Repairs to Intrinsically Safe Components<ul><li>Replace intrinsically safe components, rather than repair them.&#xA0;</li></ul>Cabling<ul><li>Do not expose the cabling to wear, corrosion, excessive pressure, vibration, sharp edges, or other adverse environmental factors.&#xA0;</li><li>Consider the long-term effects of aging and continuous vibration from components, such as compressors and fans.&#xA0;</li></ul>Detection of Flammable Refrigerants<ul><li>Do not use potential sources of ignition for refrigerant leak detection under any circumstances.&#xA0;</li><li>Use electronic leak detectors to detect leaks in systems containing flammable refrigerants.&#xA0;<ul><li>Set the detector to a percentage of the refrigerant&apos;s lower flammability limit (LFL).</li><li>Calibrate the detector to confirm that the appropriate gas concentration does not exceed 25% of the LFL.&#xA0;</li></ul></li><li>Use leak detection fluids to detect leaks in systems containing flammable refrigerants.&#xA0;<ul><li>This method is suitable for most refrigerants but must not contain chlorine. Chlorine can react with the refrigerant and corrode copper piping.&#xA0;</li></ul></li><li>If a leak is suspected, remove or extinguish all open flames.&#xA0;</li><li>If a refrigerant leak requiring brazing is detected, fully recover the refrigerant or isolate the refrigerant using the shut-off valves to prevent accidental release. Purge oxygen-free nitrogen through the system before and during brazing.&#xA0;</li></ul>

Service Information for A2L Refrigerants

Chat with one of our friendly reps to get help quick.

Something on your mind not found here? E-mail us.

We offer phone support if you don't want to type.

Support Center

Get information on flushing, removing, and evacuating A2L refrigerants.

A2L Safety Requirements

Product Data & Technical Information

Pioneer Offers Hyper-Heat Units

Pioneer Systems Offer Both Heating & Cooling Functions

Understand the Difference Between 115V & 230V Systems

Understand the Refrigerants Used for Each Model

How to Choose a System

Mini Splits are Capable of Using Fewer Indoor Units than the Outdoor Unit’s Zonal Capacity

Pioneer Mini Splits Function as Dehumidifiers

Pioneer Offers Different Lineset Lengths

Pioneer Offers Pre-Charged Linesets

Pioneer Offers Pre-Flared Linesets

Pioneer Systems Include Factory Pre-Charged Refrigerant

Single-Zone Mini Splits Cannot be Used with Multiple Indoor Units

Understand how Mini Splits are Powered

Understand the Life Expectancy of Pioneer Systems

Understand the Meaning of “Multi-Zone”

Mini-Split Basics

Determine the Unit Size Needed for Your Space

Match the Lineset Diameter to Your Pioneer Indoor Unit

Understand Why Short Cycling Occurs When Sizing Systems

Sizing & Efficiency Guide

Start Here

Understand the Differences Between Inverter+ & Inverter++ Systems

Understand the Differences Between the Wall-Mounted Ductless Mini Splits

Understand Which Units are Rated Energy-Star

Compare Models

Learn About the Discounts Available

Learn About the Energy-Star Tax Credits Available for Pioneer Systems

Learn More about IRA Tax Credits

Learn Why Your Pioneer Discount Code Only Says "SAMPLE"

Redeem Your Pioneer Rewards Points When Shopping Online

Understand How to Manage Multiple Credit Card Charges with Pioneer

Financing & Payment

Learn About Our Shipping & Delivery Details

Understand the Qualifications for Free Shipping

Order Status & Shipping

Diamante Essenza High-Wall (WYT-17) Overview

Diamante Pro High-Wall (WYT-20) Overview

Quantum Fresh High-Wall (WYT-FA) Overview

Quantum Hyperformance High-Wall (WYT-25) Overview

Quantum Ultra Ceiling Cassette (CYT-24) Overview

Quantum Ultra Ducted Ceiling Concealed (RYT-24) Overview

Quantum Ultra Floor-Ceiling Flex (UYT-24) Overview

Quantum Ultra High-Wall (WYT-24) Overview

Quantum Ultra Multi-Zone Overview

Vertex Ducted Central Split (DYC-18) Overview

Ducted & Ductless Systems

ECOasis 50 Ductless Wall-Mounted Single-Room Energy Recovery Ventilator (ERV) Overview

ECOasis 150 Ductless Wall-Mounted Single-Room Energy Recovery Ventilator (ERV) Overview

Energy Recovery Ventilators

QHD070 Whole-House Ducted Dehumidifier (QHD) Overview

High Performance Dehumidifier

Full Inverter Rooftop RV Air Conditioner Heat Pump (PYZ) Overview

Under-Bench RV Inverter Packaged Heat Pump Air Conditioner (PYR) Overview

Recreational Vehicle Systems

Product Line Overviews

Find Out How to Complete Returns

Figure Out How to Start Your Return

Learn About Our Policy for Undeliverable or Refused Shipments

Learn About Our Return Policy

Understand How to Return an Item

Understand the Eligibility Requirements for Refunds

Understand Our Return Fees

Understand Our Return Process

Returns & Refunds

Shopping & Pre-Purchase

Find an Installer for Your System

Find Professionals to Install Your Pioneer System

Learn Who is Permitted to Install Your System

Understand if Our Systems can be Self-Installed

Understand the Cost & Time Spent on Installing Systems

First-Time Setup

Connect the Refrigerant Piping to the Indoor Unit

Cassette Units

Ducted Units

Flex Units

Wall-Mounted Units

Indoor Units

Angle Linesets Upward

Complete the Safety Checks & Test Run

Find Out if a Wall-Mounted Indoor Unit can be Set onto Ceilings

Find Out if the Indoor Unit Requires Anything Extra in Order to be Wall-Mounted

Find Out the Ideal Height for Mounting Indoor Units

Leakage Inspection & Vacuuming for Refrigerant Lines

Learn the Gauge of Wire Used for Ductless System Connections

Open the Service Valve

Set Up the Lineset to Exit from the Side of the Indoor Unit

Understand the 6-Foot Plastic Whips & 4-Lead Mini Split Connection Wire

Understand how to Properly Uncoil the Lineset

Understand the Drilling Details to Accommodate Drain & Refrigerant Lines

Understand the Requirements for Installing Your System

Understand the Torque Wrench Size for Installing Your System

Installation Requirements

Understand the Allowable Zone Combinations for Multi-Zone Systems

Multi-Zone Units

Install Outdoor Units: Getting Started

Air Evacuation & Bleed the Circuit for Outdoor Units

Connect the Electrical Wiring for Outdoor Units

Connect the Refrigerant Piping to the Outdoor Unit

Mount the Outdoor Unit

Select the Installation Location for Outdoor Units

Select the Installation Location for Ducted Central Split Outdoor Units

Set Up the Condensate Water Drainage for Outdoor Units

Understand How to Install Ducted Central Split Outdoor Units on Support Pads

Outdoor Units

Ductless & Ducted Systems

Install ECOasis 50 Energy Recovery Ventilators

Install ECOasis 150 Energy Recover Ventilators

Energy Recovery Ventilator

Connect the Drain Fitting for QHD070 Whole-House Ducted Dehumidifiers

High Performance Dehumidifiers

Install Rooftop RV Systems: Getting Started

Create the Roof Opening for Rooftop RV Systems

Install the Air Duct & Top Mounting Plate for Rooftop RV Systems

Mount the Panel for Rooftop RV Systems

Place the Unit onto the Roof for Rooftop RV Systems

Setup the Electrical Wiring for Rooftop RV Systems

Setup the System Connections for Rooftop RV Systems

Understand the Installation Requirements for Rooftop RV Systems

Rooftop RV Inverter

Install Under-Bench RV Systems: Getting Started

Connect & Power Up Under-Bench RV Systems

Create the Floor Openings for Under-Bench RV Systems

Create the Recirculation Air Opening for Under-Bench RV Systems

Fasten the Under-Bench RV System into Place

Install the Wall Thermostat for Under-Bench RV Systems

Understand the Ductwork Best Practices for Under-Bench RV Systems

Understand the Installation Requirements for Under-Bench RV Systems

Under-Bench RV Inverter

Installation & Setup

Understand the DIP Switches for Vertex Ducted Central Split Systems

DIP Switch Layouts

Turn the LED Display On or Off

Understand the Display Board for Ducted Ceiling Concealed Systems

Understand the Display Panel for Rooftop RV Systems

Understand the Front Panel Displays for Ceiling Cassette Systems

Understand the Front Panel Display for Floor-Ceiling Flex Systems

Understand the Front Panel Display for Wall-Mounted Systems

Understand the Master Unit Display for ECOasis 50 Energy Recovery Ventilators

Understand the Onboard Controller & Terminal Block Layout for QHD070 Whole-House Ducted Dehumidifiers